X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fbf533-stamp.h;h=4be2a5cfb8cf156d5620363a5fa7c7356e3425d5;hb=84efbf4d144ff8aaed3cca036aebb1fe69eff3f4;hp=79a1404a40db3e3ed291b9950c5faeac3248b914;hpb=1d10b9e99d1b4a6a880d424ec791cde45cb04614;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h index 79a1404..4be2a5c 100644 --- a/include/configs/bf533-stamp.h +++ b/include/configs/bf533-stamp.h @@ -2,466 +2,258 @@ * U-boot - Configuration file for BF533 STAMP board */ -#ifndef __CONFIG_STAMP_H__ -#define __CONFIG_STAMP_H__ +#ifndef __CONFIG_BF533_STAMP_H__ +#define __CONFIG_BF533_STAMP_H__ -#define CONFIG_STAMP 1 -#define CONFIG_RTC_BFIN 1 -#define CONFIG_BF533 1 -/* - * Boot Mode Set - * Blackfin can support several boot modes - */ -#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */ -#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */ -#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */ -/* Define the boot mode */ -#define BFIN_BOOT_MODE BF533_BYPASS_BOOT -/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */ - -#define CONFIG_PANIC_HANG 1 - -#define ADSP_BF531 0x31 -#define ADSP_BF532 0x32 -#define ADSP_BF533 0x33 -#define BFIN_CPU ADSP_BF533 - -/* This sets the default state of the cache on U-Boot's boot */ -#define CONFIG_ICACHE_ON -#define CONFIG_DCACHE_ON - -/* Define where the uboot will be loaded by on-chip boot rom */ -#define APP_ENTRY 0x00001000 +#include -/* - * Stringize definitions - needed for environmental settings - */ -#define STRINGIZE2(x) #x -#define STRINGIZE(x) STRINGIZE2(x) /* - * Board settings + * Processor Settings */ -#define CONFIG_DRIVER_SMC91111 1 -#define CONFIG_SMC91111_BASE 0x20300300 - -/* FLASH/ETHERNET uses the same address range */ -#define SHARED_RESOURCES 1 +#define CONFIG_BFIN_CPU bf533-0.3 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS -/* Is I2C bit-banged? */ -#define CONFIG_SOFT_I2C 1 /* - * Software (bit-bang) I2C driver configuration + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV */ -#define PF_SCL PF3 -#define PF_SDA PF2 +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 11059200 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 45 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 6 /* note: 1.2 boards can go faster */ -/* - * Video splash screen support - */ -#define CONFIG_VIDEO 0 - -#define CONFIG_VDSP 1 /* - * Clock settings + * Memory Settings */ +#define CONFIG_MEM_ADD_WDTH 11 +#define CONFIG_MEM_SIZE 128 -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 11059200 -/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ -/* 1=CLKIN/2 */ -#define CONFIG_CLKIN_HALF 0 -/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ -/* 1=bypass PLL */ -#define CONFIG_PLL_BYPASS 0 -/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ -/* Values can range from 1-64 */ -#define CONFIG_VCO_MULT 36 -/* CONFIG_CCLK_DIV controls what the core clock divider is */ -/* Values can be 1, 2, 4, or 8 ONLY */ -#define CONFIG_CCLK_DIV 1 -/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/ -/* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 5 -/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ -/* Values can range from 2-65535 */ -/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ -#define CONFIG_SPI_BAUD 2 - -#if (BFIN_BOOT_MODE == BF533_SPI_BOOT) -#define CONFIG_SPI_BAUD_INITBLOCK 4 -#endif - -/* - * Network settings - */ +#define CONFIG_EBIU_SDRRC_VAL 0x268 +#define CONFIG_EBIU_SDGCTL_VAL 0x911109 -#if (CONFIG_DRIVER_SMC91111) -#if 0 -#define CONFIG_MII -#endif +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3 +#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983 -/* network support */ -#define CONFIG_IPADDR 192.168.0.15 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_GATEWAYIP 192.168.0.1 -#define CONFIG_SERVERIP 192.168.0.2 -#define CONFIG_HOSTNAME STAMP -#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) -/* To remove hardcoding and enable MAC storage in EEPROM */ -/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ -#endif /* CONFIG_DRIVER_SMC91111 */ /* - * Flash settings + * Network Settings */ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_DRIVER_SMC91111 1 +#define CONFIG_SMC91111_BASE 0x20300300 +#define SMC91111_EEPROM_INIT() \ + do { \ + *pFIO_DIR |= PF1; \ + *pFIO_FLAG_S = PF1; \ + SSYNC(); \ + } while (0) +#define CONFIG_HOSTNAME bf533-stamp +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ -#define CFG_FLASH_CFI /* The flash is CFI compatible */ -#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CFG_FLASH_CFI_AMD_RESET - -#define CFG_FLASH_BASE 0x20000000 -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ - -#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_ADDR 0x20004000 -#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE) -#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT) -#define CFG_ENV_IS_IN_EEPROM 1 -#define CFG_ENV_OFFSET 0x4000 -#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */ -#endif - -#define CFG_ENV_SIZE 0x2000 -#define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */ -#define ENV_IS_EMBEDDED - -#define CFG_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */ -#define CFG_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ - -/* JFFS Partition offset set */ -#define CFG_JFFS2_FIRST_BANK 0 -#define CFG_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CFG_JFFS2_FIRST_SECTOR 11 - -/* - * following timeouts shall be used once the - * Flash real protection is enabled - */ -#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */ -#define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */ /* - * SDRAM settings & memory map + * Flash Settings */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_CFI_AMD_RESET +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 67 -#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */ -#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */ -#define CONFIG_MEM_MT48LC64M4A2FB_7E 1 - -#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) -#define CFG_MEMTEST_START 0x00000000 /* memtest works on */ -#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT) -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#endif - -#define CFG_SDRAM_BASE 0x00000000 - -#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024) -#define CFG_MEMTEST_END (CFG_MAX_RAM_SIZE - 0x80000 - 1) -#define CONFIG_LOADADDR 0x01000000 - -#define CFG_LOAD_ADDR CONFIG_LOADADDR -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CFG_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */ -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ - -#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - 0x40000) -#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN) -#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE) -#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4) - -/* Check to make sure everything fits in SDRAM */ -#if ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) > CFG_MAX_RAM_SIZE) - #error Memory Map does not fit into configuration -#endif - -#if ( CONFIG_CLKIN_HALF == 0 ) -#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) -#else -#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) -#endif - -#if (CONFIG_PLL_BYPASS == 0) -#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) -#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) -#else -#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ -#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ -#endif - -#if (BFIN_BOOT_MODE == BF533_SPI_BOOT) -#if (CONFIG_SCLK_HZ / (2*CONFIG_SPI_BAUD) > 20000000) -#define CONFIG_SPI_FLASH_FAST_READ 1 /* Needed if SPI_CLK > 20 MHz */ -#else -#undef CONFIG_SPI_FLASH_FAST_READ -#endif -#endif /* - * Command settings + * SPI Settings */ +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ATMEL +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_WINBOND -#define CFG_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 - -#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) -#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */ -#endif - -/* configuration lookup from the BOOTP/DHCP server, */ -/* but not try to load any image using TFTP */ - -#define CONFIG_BOOTDELAY 5 -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ -#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) -#define CONFIG_BOOTCOMMAND "run ramboot" -#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT) -#define CONFIG_BOOTCOMMAND "eeprom read 0x1000000 0x100000 0x180000;icache on;dcache on;bootm 0x1000000" -#endif - -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" - -#if (CONFIG_DRIVER_SMC91111) -#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \ - CFG_CMD_PING | \ - CFG_CMD_ELF | \ - CFG_CMD_CACHE | \ - CFG_CMD_JFFS2 | \ - CFG_CMD_EEPROM | \ - CFG_CMD_DATE) - -#else -#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \ - CFG_CMD_ELF | \ - CFG_CMD_CACHE | \ - CFG_CMD_JFFS2 | \ - CFG_CMD_EEPROM | \ - CFG_CMD_DATE) -#endif - -#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) -#if (CONFIG_DRIVER_SMC91111) -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ - "$(rootpath) console=ttyBF0,57600\0" \ - "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ - "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ - "ramboot=tftpboot $(loadaddr) linux; " \ - "run ramargs;run addip;bootelf\0" \ - "nfsboot=tftpboot $(loadaddr) linux; " \ - "run nfsargs;run addip;bootelf\0" \ - "flashboot=bootm 0x20100000\0" \ - "update=tftpboot $(loadaddr) u-boot.bin; " \ - "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \ - "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \ - "" -#else -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "flashboot=bootm 0x20100000\0" \ - " -#endif - -#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT) -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ - "$(rootpath) console=ttyBF0,57600\0" \ - "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ - "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ - "ramboot=tftpboot $(loadaddr) linux; " \ - "run ramargs;run addip;bootelf\0" \ - "nfsboot=tftpboot $(loadaddr) linux; " \ - "run nfsargs;run addip;bootelf\0" \ - "flashboot=bootm 0x20100000\0" \ - "update=tftpboot $(loadaddr) u-boot.ldr;" \ - "eeprom write $(loadaddr) 0x0 $(filesize);\0"\ - "" -#endif - -#ifdef CONFIG_SOFT_I2C -#if (!CONFIG_SOFT_I2C) -#undef CONFIG_SOFT_I2C -#endif -#endif - -#if (CONFIG_SOFT_I2C) -#define CONFIG_COMMANDS2 CFG_CMD_I2C -#else -#define CONFIG_COMMANDS2 0 -#endif /* CONFIG_SOFT_I2C */ - -#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT) -#define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2 | CFG_CMD_DHCP) -#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT) -#define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2) -#endif - -/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include /* - * Console settings + * Env Storage Settings */ - -#define CONFIG_BAUDRATE 57600 -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#if (BFIN_BOOT_MODE == BF533_SPI_BOOT) -#if (BFIN_CPU == ADSP_BF531) -#define CFG_PROMPT "serial_bf531> " /* Monitor Command Prompt */ -#elif (BFIN_CPU == ADSP_BF532) -#define CFG_PROMPT "serial_bf532> " /* Monitor Command Prompt */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x10000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 #else -#define CFG_PROMPT "serial_bf533> " /* Monitor Command Prompt */ +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 #endif +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +#define ENV_IS_EMBEDDED #else -#if (BFIN_CPU == ADSP_BF531) -#define CFG_PROMPT "bf531> " /* Monitor Command Prompt */ -#elif (BFIN_CPU == ADSP_BF532) -#define CFG_PROMPT "bf532> " /* Monitor Command Prompt */ -#else -#define CFG_PROMPT "bf533> " /* Monitor Command Prompt */ -#endif +#define ENV_IS_EMBEDDED_CUSTOM #endif - -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#ifdef ENV_IS_EMBEDDED +/* WARNING - the following is hand-optimized to fit within + * the sector before the environment sector. If it throws + * an error during compilation remove an object here to get + * it linked after the configuration sector. + */ +# define LDS_BOARD_TEXT \ + cpu/blackfin/traps.o (.text .text.*); \ + cpu/blackfin/interrupt.o (.text .text.*); \ + cpu/blackfin/serial.o (.text .text.*); \ + common/dlmalloc.o (.text .text.*); \ + lib_generic/crc32.o (.text .text.*); \ + . = DEFINED(env_offset) ? env_offset : .; \ + common/env_embedded.o (.text .text.*); #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_LOADS_ECHO 1 /* - * I2C settings + * I2C Settings * By default PF2 is used as SDA and PF3 as SCL on the Stamp board */ -#if (CONFIG_SOFT_I2C) - -#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;") -#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;") -#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;") -#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;") -#define I2C_SDA(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SDA; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SDA; \ - asm("ssync;"); \ - } -#define I2C_SCL(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SCL; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SCL; \ - asm("ssync;"); \ - } +#define CONFIG_SOFT_I2C +#ifdef CONFIG_SOFT_I2C +#define PF_SCL PF3 +#define PF_SDA PF2 +#define I2C_INIT \ + do { \ + *pFIO_DIR |= PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_ACTIVE \ + do { \ + *pFIO_DIR |= PF_SDA; \ + *pFIO_INEN &= ~PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_TRISTATE \ + do { \ + *pFIO_DIR &= ~PF_SDA; \ + *pFIO_INEN |= PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0) +#define I2C_SDA(bit) \ + do { \ + if (bit) \ + *pFIO_FLAG_S = PF_SDA; \ + else \ + *pFIO_FLAG_C = PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_SCL(bit) \ + do { \ + if (bit) \ + *pFIO_FLAG_S = PF_SCL; \ + else \ + *pFIO_FLAG_C = PF_SCL; \ + SSYNC(); \ + } while (0) #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#define CFG_I2C_SPEED 50000 -#define CFG_I2C_SLAVE 0xFE -#endif /* CONFIG_SOFT_I2C */ +#define CONFIG_SYS_I2C_SPEED 50000 +#define CONFIG_SYS_I2C_SLAVE 0 +#endif + /* - * Compact Flash settings + * Compact Flash / IDE / ATA Settings */ /* Enabled below option for CF support */ -/* #define CONFIG_STAMP_CF 1 */ - -#if defined(CONFIG_STAMP_CF) && (CONFIG_COMMANDS & CFG_CMD_IDE) - -#define CONFIG_MISC_INIT_R 1 +/* #define CONFIG_STAMP_CF */ +#if defined(CONFIG_STAMP_CF) +#define CONFIG_MISC_INIT_R #define CONFIG_DOS_PARTITION 1 -/* - * IDE/ATA stuff - */ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ #undef CONFIG_IDE_LED /* no led for ide supported */ #undef CONFIG_IDE_RESET /* no reset for ide supported */ -#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */ -#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) + +#define CONFIG_SYS_ATA_BASE_ADDR 0x20200000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CFG_ATA_BASE_ADDR 0x20200000 -#define CFG_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* alternate registers */ -#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */ -#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */ -#define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_STRIDE 2 -#define CFG_ATA_STRIDE 2 +#undef CONFIG_EBIU_AMBCTL1_VAL +#define CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2 #endif + /* - * Miscellaneous configurable options + * Misc Settings */ +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 0 -#define CFG_HZ 1000 /* 1ms time tick */ - -#define CFG_BOOTM_LEN 0x4000000/* Large Image Length, set to 64 Meg */ - -#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ - -#define CONFIG_SPI +/* FLASH/ETHERNET uses the same async bank */ +#define SHARED_RESOURCES 1 -#ifdef CONFIG_VIDEO -#if (CONFIG_VIDEO) -#define CONFIG_SPLASH_SCREEN 1 -#define CONFIG_SILENT_CONSOLE 1 -#else -#undef CONFIG_VIDEO +/* define to enable boot progress via leds */ +/* #define CONFIG_SHOW_BOOT_PROGRESS */ + +/* define to enable run status via led */ +/* #define CONFIG_STATUS_LED */ +#ifdef CONFIG_STATUS_LED +#define CONFIG_BOARD_SPECIFIC_LED +#ifndef __ASSEMBLY__ +typedef unsigned int led_id_t; +void __led_init(led_id_t mask, int state); +void __led_set(led_id_t mask, int state); +void __led_toggle(led_id_t mask); #endif +/* use LED1 to indicate booting/alive */ +#define STATUS_LED_BOOT 0 +#define STATUS_LED_BIT 1 +#define STATUS_LED_STATE STATUS_LED_ON +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) +/* use LED2 to indicate crash */ +#define STATUS_LED_CRASH 1 +#define STATUS_LED_BIT1 2 +#define STATUS_LED_STATE1 STATUS_LED_ON +#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) #endif +/* define to enable splash screen support */ +/* #define CONFIG_VIDEO */ + + /* - * FLASH organization and environment definitions + * Pull in common ADI header for remaining command/environment setup */ -#define CFG_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */ - -/* 0xFF, 0xBBC3BBc3, 0x99B39983 */ -/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN) -#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \ - B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN) -#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \ - B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN) -*/ -#define AMGCTLVAL 0xFF -#define AMBCTL0VAL 0xBBC3BBC3 -#define AMBCTL1VAL 0x99B39983 -#define CF_AMBCTL1VAL 0x99B3ffc2 - -#ifdef CONFIG_VDSP -#define ET_EXEC_VDSP 0x8 -#define SHT_STRTAB_VDSP 0x1 -#define ELFSHDRSIZE_VDSP 0x2C -#define VDSP_ENTRY_ADDR 0xFFA00000 -#endif +#include #endif