X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fbcm28155_ap.h;h=781689a991451921e52a483e1dd18d1600769410;hb=0223462b373b975d970fa86e5e1a7eadd1d41820;hp=0882531509c145af361f839ebadc70affaa13760;hpb=45a68fe267f14aae05c5d244b1bcda075de7d0a6;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/bcm28155_ap.h b/include/configs/bcm28155_ap.h
index 0882531..781689a 100644
--- a/include/configs/bcm28155_ap.h
+++ b/include/configs/bcm28155_ap.h
@@ -1,7 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2013 Broadcom Corporation.
- *
- * SPDX-License-Identifier:      GPL-2.0+
  */
 
 #ifndef __BCM28155_AP_H
@@ -17,21 +16,16 @@
 /*
  * Memory configuration
  */
-#define CONFIG_SYS_TEXT_BASE		0xae000000
 
 #define CONFIG_SYS_SDRAM_BASE		0x80000000
 #define CONFIG_SYS_SDRAM_SIZE		0x80000000
-#define CONFIG_NR_DRAM_BANKS		1
 
 #define CONFIG_SYS_MALLOC_LEN		SZ_4M	/* see armv7/start.S. */
-#define CONFIG_STACKSIZE		SZ_256K
 
 /* GPIO Driver */
 #define CONFIG_KONA_GPIO
 
 /* MMC/SD Driver */
-#define CONFIG_GENERIC_MMC
-
 #define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR
 #define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR
 #define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR
@@ -60,7 +54,6 @@
 #define CONFIG_SYS_TIMER_COUNTER	(TIMER_BASE_ADDR + 4) /* STCLO offset */
 
 /* Init functions */
-#define CONFIG_MISC_INIT_R	/* board's misc_init_r function */
 
 /* Some commands use this as the default load address */
 #define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE
@@ -79,23 +72,15 @@
 /* Post pad 3 bytes after each reg addr */
 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
 #define CONFIG_SYS_NS16550_CLK		13000000
-#define CONFIG_CONS_INDEX		1
 #define CONFIG_SYS_NS16550_COM1		0x3e000000
 
-#define CONFIG_BAUDRATE			115200
-
 /* must fit into GPT:u-boot-env partition */
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV		0
 #define CONFIG_ENV_OFFSET		(0x00011a00 * 512)
 #define CONFIG_ENV_SIZE			(8 * 512)
 
-#define CONFIG_SYS_NO_FLASH	/* Not using NAND/NOR unmanaged flash */
-
 /* console configuration */
 #define CONFIG_SYS_CBSIZE		1024	/* Console buffer size */
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
-			sizeof(CONFIG_SYS_PROMPT) + 16)	/* Printbuffer size */
 #define CONFIG_SYS_MAXARGS		64
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
 
@@ -104,23 +89,14 @@
  * This is necessary for the fatls command to work on an SD card
  * for example.
  */
-#define CONFIG_DOS_PARTITION
-#define CONFIG_EFI_PARTITION
 
 /* version string, parser, etc */
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_LONGHELP
 
-#define CONFIG_CRC32_VERIFY
 #define CONFIG_MX_CYCLIC
 
 /* Initial upstream - boot to cmd prompt only */
 #define CONFIG_BOOTCOMMAND		""
 
-/* Commands */
-#define CONFIG_FAT_WRITE
-
 #define CONFIG_USBID_ADDR		0x34052c46
 
 #endif /* __BCM28155_AP_H */