X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fbamboo.h;h=31c725f011323f51c328f13c6cc9f18135de7f92;hb=0e8d158664a913392cb01fb11a948d83f72e105e;hp=763d1c7a8b48632df13d9868ddf4c958362ca71e;hpb=83b75ef3a6d87b540368d6721728332c919e51bb;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index 763d1c7..31c725f 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -32,9 +32,16 @@ *----------------------------------------------------------------------*/ #define CONFIG_BAMBOO 1 /* Board is BAMBOO */ #define CONFIG_440EP 1 /* Specific PPC440EP support */ +#define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME bamboo +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ /* @@ -48,10 +55,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 @@ -73,9 +76,9 @@ * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ #define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ -#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ +#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ #define CFG_INIT_RAM_END (4 << 10) -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET @@ -83,14 +86,9 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * NVRAM/RTC * @@ -105,17 +103,17 @@ * Environment *----------------------------------------------------------------------*/ #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) -#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #else -#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ -#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */ +#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */ #endif /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_MAX_FLASH_BANKS 3 /* number of banks */ -#define CFG_MAX_FLASH_SECT 256 /* sectors per device */ +#define CFG_MAX_FLASH_BANKS 3 /* number of banks */ +#define CFG_MAX_FLASH_SECT 256 /* sectors per device */ #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ @@ -125,18 +123,18 @@ #define CFG_FLASH_ADDR1 0x2aa #define CFG_FLASH_WORD_SIZE unsigned char -#define CFG_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */ -#define CFG_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */ +#define CFG_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */ +#define CFG_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */ -#ifdef CFG_ENV_IS_IN_FLASH -#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR ((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) -#endif /* CFG_ENV_IS_IN_FLASH */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) +#endif /* CONFIG_ENV_IS_IN_FLASH */ /* * IPL (Initial Program Loader, integrated inside CPU) @@ -185,14 +183,14 @@ #define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) #define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} -#ifdef CFG_ENV_IS_IN_NAND +#ifdef CONFIG_ENV_IS_IN_NAND /* * For NAND booting the environment is embedded in the U-Boot image. Please take * look at the file board/amcc/sequoia/u-boot-nand.lds for details. */ -#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE -#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE) -#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#define CONFIG_ENV_SIZE CFG_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) #endif /*----------------------------------------------------------------------- @@ -221,14 +219,12 @@ #define CFG_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */ #define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51} #define CFG_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */ +#define CONFIG_PROG_SDRAM_TLB /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -237,58 +233,25 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#ifdef CFG_ENV_IS_IN_EEPROM -#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */ -#define CFG_ENV_OFFSET 0x0 -#endif /* CFG_ENV_IS_IN_EEPROM */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS +#ifdef CONFIG_ENV_IS_IN_EEPROM +#define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */ +#define CONFIG_ENV_OFFSET 0x0 +#endif /* CONFIG_ENV_IS_IN_EEPROM */ +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=bamboo\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/bamboo/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b 100000 fffa0000 60000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load;run update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_HAS_ETH0 #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY1_ADDR 1 @@ -296,16 +259,6 @@ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #endif /* CONFIG_BAMBOO_NAND */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - #ifdef CONFIG_440EP /* USB */ #define CONFIG_USB_OHCI @@ -315,67 +268,27 @@ #define USB_2_0_DEVICE #endif /*CONFIG_440EP*/ -#ifdef CONFIG_BAMBOO_NAND -#define _CFG_CMD_NAND CFG_CMD_NAND -#else -#define _CFG_CMD_NAND 0 -#endif /* CONFIG_BAMBOO_NAND */ - -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_ASKENV | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_DIAG | \ - CFG_CMD_ELF | \ - CFG_CMD_EEPROM | \ - CFG_CMD_I2C | \ - CFG_CMD_IRQ | \ - CFG_CMD_MII | \ - CFG_CMD_NET | \ - CFG_CMD_NFS | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SDRAM | \ - CFG_CMD_USB | \ - CFG_CMD_FAT | \ - CFG_CMD_EXT2 | \ - _CFG_CMD_NAND | \ - CFG_CMD_SNTP ) - -#define CONFIG_SUPPORT_VFAT - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include - /* - * Miscellaneous configurable options + * Commands additional to the ones defined in amcc-common.h */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_CMD_DATE +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ +#ifdef CONFIG_BAMBOO_NAND +#define CONFIG_CMD_NAND +#endif -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SUPPORT_VFAT -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION /*----------------------------------------------------------------------- * PCI stuff @@ -388,39 +301,10 @@ #define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ /* Board-specific PCI */ -#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ #define CFG_PCI_TARGET_INIT #define CFG_PCI_MASTER_INIT #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif #endif /* __CONFIG_H */