X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fastro_mcf5373l.h;h=af03b303c452bd4282705684fd5729afb54e1c3b;hb=5abc1a4523a5509ce37bc3ec818b660a48f4eafd;hp=7b9ff8fb23afbda6a367314e14ffbd7edc88d576;hpb=e536ab8849b2b4f6d68bbc8e1d1f9bc033db06bd;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h
index 7b9ff8f..af03b30 100644
--- a/include/configs/astro_mcf5373l.h
+++ b/include/configs/astro_mcf5373l.h
@@ -42,8 +42,6 @@
 #define CONFIG_ASTRO5373L		/* define board type */
 
 /* Command line configuration */
-#include <config_cmd_default.h>
-
 /*
  * CONFIG_RAM defines if u-boot is loaded via BDM (or started from
  * a different bootloader that has already performed RAM setup) or
@@ -59,30 +57,8 @@
 #define ENABLE_JFFS	1
 #endif
 
-/* Define which commmands should be available at u-boot command prompt */
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MISC
-#define CONFIG_CMD_XIMG
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-#if ENABLE_JFFS
-#define CONFIG_CMD_JFFS2
-#endif
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_FPGA
-#define CONFIG_CMD_FPGA_LOADMK
 #define CONFIG_CMDLINE_EDITING
 
-#define CONFIG_SYS_HUSH_PARSER
-
 #define CONFIG_MCFRTC
 #undef RTC_DEBUG
 
@@ -119,8 +95,6 @@
  * in u-boot command interface
  */
 
-#define CONFIG_BAUDRATE		115200
-
 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(2)
 #define CONFIG_SYS_UART2_ALT3_GPIO
@@ -144,7 +118,6 @@
 #ifndef CONFIG_MONITOR_IS_IN_RAM
 #define CONFIG_ENV_OFFSET		0x1FF8000
 #define CONFIG_ENV_SECT_SIZE		0x8000
-#define CONFIG_ENV_IS_IN_FLASH		1
 #else
 /*
  * environment in RAM - This is used to use a single PC-based application
@@ -154,7 +127,6 @@
  */
 #define CONFIG_ENV_ADDR		0x40060000
 #define CONFIG_ENV_SECT_SIZE	0x8000
-#define CONFIG_ENV_IS_IN_FLASH	1
 #endif
 
 /* here we put our FPGA configuration... */
@@ -165,19 +137,6 @@
 /* AUTOBOOT settings - booting images automatically by u-boot after power on */
 
 /*
- * used for autoboot, delay in seconds u-boot will wait before starting
- * defined (auto-)boot command, setting to -1 disables delay, setting to
- * 0 will too prevent access to u-boot command interface: u-boot then has
- * to be reflashed
- * beware - watchdog is not serviced during autoboot delay time!
- */
-#ifdef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_BOOTDELAY	1
-#else
-#define CONFIG_BOOTDELAY	1
-#endif
-
-/*
  * The following settings will be contained in the environment block ; if you
  * want to use a neutral environment all those settings can be manually set in
  * u-boot: 'set' command
@@ -214,12 +173,6 @@
 #endif
 #endif
 
-/* default bootargs that are considered during boot */
-#define CONFIG_BOOTARGS		" console=ttyS2,115200 rootfstype=romfs"\
-				" loaderversion=$loaderversion"
-
-#define CONFIG_SYS_PROMPT	"URMEL > "
-
 /* default RAM address for user programs */
 #define CONFIG_SYS_LOAD_ADDR	0x20000
 
@@ -235,10 +188,8 @@
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
 
 #define CONFIG_FPGA_COUNT	1
-#define CONFIG_FPGA
 #define	CONFIG_FPGA_XILINX
 #define	CONFIG_FPGA_SPARTAN3
-#define CONFIG_FPGA_ALTERA
 #define CONFIG_FPGA_CYCLON2
 #define CONFIG_SYS_FPGA_PROG_FEEDBACK
 #define CONFIG_SYS_FPGA_WAIT		1000