X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fastro_mcf5373l.h;h=8899579faa766d89fa76cb0c00ed30ed997bfc79;hb=c9032ce168c1344fe8ffe8604825ec343ec14adf;hp=f0dd6ccb744b9c9a67d65df497bd78f44773c5d0;hpb=3765b3e7bd0f8e46914d417f29cbcb0c72b1acf7;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h
index f0dd6cc..8899579 100644
--- a/include/configs/astro_mcf5373l.h
+++ b/include/configs/astro_mcf5373l.h
@@ -39,21 +39,9 @@
 #error No card type defined!
 #endif
 
-/*
- * Define processor
- * possible values for Urmel board: only Coldfire M5373 processor supported
- * (please do not change)
- */
-
-/* it seems not clear yet which processor defines we should use */
-#define CONFIG_MCF537x			/* define processor family */
-#define CONFIG_MCF532x			/* define processor family */
-#define CONFIG_M5373			/* define processor type */
 #define CONFIG_ASTRO5373L		/* define board type */
 
 /* Command line configuration */
-#include <config_cmd_default.h>
-
 /*
  * CONFIG_RAM defines if u-boot is loaded via BDM (or started from
  * a different bootloader that has already performed RAM setup) or
@@ -69,29 +57,15 @@
 #define ENABLE_JFFS	1
 #endif
 
-/* Define which commmands should be available at u-boot command prompt */
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MISC
-#define CONFIG_CMD_XIMG
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
+/* Define which commands should be available at u-boot command prompt */
+
 #if ENABLE_JFFS
 #define CONFIG_CMD_JFFS2
 #endif
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_FPGA_LOADMK
 #define CONFIG_CMDLINE_EDITING
 
-#define CONFIG_SYS_HUSH_PARSER
-
 #define CONFIG_MCFRTC
 #undef RTC_DEBUG
 
@@ -110,10 +84,8 @@
 /*
  * Defines processor clock - important for correct timings concerning serial
  * interface etc.
- * CONFIG_SYS_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms
  */
 
-#define CONFIG_SYS_HZ			1000
 #define CONFIG_SYS_CLK			80000000
 #define CONFIG_SYS_CPU_CLK		(CONFIG_SYS_CLK * 3)
 #define CONFIG_SYS_SDRAM_SIZE		32		/* SDRAM size in MB */
@@ -130,8 +102,6 @@
  * in u-boot command interface
  */
 
-#define CONFIG_BAUDRATE		115200
-
 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(2)
 #define CONFIG_SYS_UART2_ALT3_GPIO
@@ -176,19 +146,6 @@
 /* AUTOBOOT settings - booting images automatically by u-boot after power on */
 
 /*
- * used for autoboot, delay in seconds u-boot will wait before starting
- * defined (auto-)boot command, setting to -1 disables delay, setting to
- * 0 will too prevent access to u-boot command interface: u-boot then has
- * to be reflashed
- * beware - watchdog is not serviced during autoboot delay time!
- */
-#ifdef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_BOOTDELAY	1
-#else
-#define CONFIG_BOOTDELAY	1
-#endif
-
-/*
  * The following settings will be contained in the environment block ; if you
  * want to use a neutral environment all those settings can be manually set in
  * u-boot: 'set' command
@@ -229,8 +186,6 @@
 #define CONFIG_BOOTARGS		" console=ttyS2,115200 rootfstype=romfs"\
 				" loaderversion=$loaderversion"
 
-#define CONFIG_SYS_PROMPT	"URMEL > "
-
 /* default RAM address for user programs */
 #define CONFIG_SYS_LOAD_ADDR	0x20000
 
@@ -354,6 +309,10 @@
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
 #define CONFIG_SYS_FLASH_CFI_NONBLOCK	1
 
+#define LDS_BOARD_TEXT \
+	. = DEFINED(env_offset) ? env_offset : .; \
+	common/env_embedded.o       (.text*)
+
 #if ENABLE_JFFS
 /* JFFS Partition offset set */
 #define CONFIG_SYS_JFFS2_FIRST_BANK    0