X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fastro_mcf5373l.h;h=4f6fb415693aa96eec307b98467c48b557feadcf;hb=0f9595b9fa68ed1634adddf989fd037909eec433;hp=2e7fbfb396ce7ed7973ba713d6687f78f2b16801;hpb=cf033e04da315ba949e804c127abae0134bda30f;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h
index 2e7fbfb..4f6fb41 100644
--- a/include/configs/astro_mcf5373l.h
+++ b/include/configs/astro_mcf5373l.h
@@ -22,23 +22,22 @@
  * set the card type to actually compile for; either of
  * the possibilities listed below has to be used!
  */
-#define CONFIG_ASTRO_V532	1
+#define ASTRO_V532	1
 
-#if CONFIG_ASTRO_V532
+#if ASTRO_V532
 #define ASTRO_ID	0xF8
-#elif CONFIG_ASTRO_V512
+#elif ASTRO_V512
 #define ASTRO_ID	0xFA
-#elif CONFIG_ASTRO_TWIN7S2
+#elif ASTRO_TWIN7S2
 #define ASTRO_ID	0xF9
-#elif CONFIG_ASTRO_V912
+#elif ASTRO_V912
 #define ASTRO_ID	0xFC
-#elif CONFIG_ASTRO_COFDMDUOS2
+#elif ASTRO_COFDMDUOS2
 #define ASTRO_ID	0xFB
 #else
 #error No card type defined!
 #endif
 
-/* Command line configuration */
 /*
  * CONFIG_RAM defines if u-boot is loaded via BDM (or started from
  * a different bootloader that has already performed RAM setup) or
@@ -57,15 +56,8 @@
 
 /* Timer */
 #define CONFIG_MCFTMR
-#undef CONFIG_MCFPIT
 
 /* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	80000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x58000
-#define CONFIG_SYS_IMMR			CONFIG_SYS_MBAR
 
 /*
  * Defines processor clock - important for correct timings concerning serial
@@ -88,7 +80,6 @@
  * in u-boot command interface
  */
 
-#define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(2)
 #define CONFIG_SYS_UART2_ALT3_GPIO
 
@@ -99,7 +90,6 @@
  */
 
 #ifndef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_WATCHDOG
 #define CONFIG_WATCHDOG_TIMEOUT 3355	/* timeout in milliseconds */
 #endif
 
@@ -109,8 +99,6 @@
  */
 
 #ifndef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_ENV_OFFSET		0x1FF8000
-#define CONFIG_ENV_SECT_SIZE		0x8000
 #else
 /*
  * environment in RAM - This is used to use a single PC-based application
@@ -118,8 +106,6 @@
  * to execute the commands from the environment. Feedback is done via setting
  * and reading memory locations.
  */
-#define CONFIG_ENV_ADDR		0x40060000
-#define CONFIG_ENV_SECT_SIZE	0x8000
 #endif
 
 /* here we put our FPGA configuration... */
@@ -152,21 +138,6 @@
  * by external update.c; This is not included in mainline because
  * it needs non-blocking CFI routines.
  */
-#ifdef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_BOOTCOMMAND	""	/* no autoboot in this case */
-#else
-#if CONFIG_ASTRO_V532
-#define CONFIG_BOOTCOMMAND	"protect off 0x80000 0x1ffffff;run env_check;"\
-				"run xilinxload&&run alteraload&&bootm 0x80000;"\
-				"update;reset"
-#else
-#define CONFIG_BOOTCOMMAND	"protect off 0x80000 0x1ffffff;run env_check;"\
-				"run xilinxload&&bootm 0x80000;update;reset"
-#endif
-#endif
-
-/* default RAM address for user programs */
-#define CONFIG_SYS_LOAD_ADDR	0x20000
 
 #define CONFIG_FPGA_COUNT	1
 #define CONFIG_SYS_FPGA_PROG_FEEDBACK
@@ -176,9 +147,6 @@
 
 /* Defines memory range for test */
 
-#define CONFIG_SYS_MEMTEST_START	0x40020000
-#define CONFIG_SYS_MEMTEST_END		0x41ffffff
-
 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
@@ -249,8 +217,6 @@
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)
 
 #define CONFIG_SYS_BOOTPARAMS_LEN	(64 * 1024)
-/* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)
 
 /*
  * For booting Linux, the board info and command line data
@@ -261,7 +227,6 @@
 						(CONFIG_SYS_SDRAM_SIZE << 20))
 
 /* FLASH organization */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1
 #define CONFIG_SYS_MAX_FLASH_SECT	259
 #define CONFIG_SYS_FLASH_ERASE_TOUT	1000
 
@@ -281,7 +246,6 @@
 #endif
 
 /* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE	16
 
 #define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - 8)