X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fastro_mcf5373l.h;h=36e351f3583357f47469c7264da969ad94e698aa;hb=74337aa4506c76e790ab45ad4f4ab854f25d19da;hp=61989d6babe2f1988081e33b6f351bffff419043;hpb=c2774e6149a6bedb0941deefec84665119e685a4;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h
index 61989d6..36e351f 100644
--- a/include/configs/astro_mcf5373l.h
+++ b/include/configs/astro_mcf5373l.h
@@ -1,9 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Configuration settings for the Sentec Cobra Board.
  *
  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 /*
@@ -23,25 +22,22 @@
  * set the card type to actually compile for; either of
  * the possibilities listed below has to be used!
  */
-#define CONFIG_ASTRO_V532	1
+#define ASTRO_V532	1
 
-#if CONFIG_ASTRO_V532
+#if ASTRO_V532
 #define ASTRO_ID	0xF8
-#elif CONFIG_ASTRO_V512
+#elif ASTRO_V512
 #define ASTRO_ID	0xFA
-#elif CONFIG_ASTRO_TWIN7S2
+#elif ASTRO_TWIN7S2
 #define ASTRO_ID	0xF9
-#elif CONFIG_ASTRO_V912
+#elif ASTRO_V912
 #define ASTRO_ID	0xFC
-#elif CONFIG_ASTRO_COFDMDUOS2
+#elif ASTRO_COFDMDUOS2
 #define ASTRO_ID	0xFB
 #else
 #error No card type defined!
 #endif
 
-#define CONFIG_ASTRO5373L		/* define board type */
-
-/* Command line configuration */
 /*
  * CONFIG_RAM defines if u-boot is loaded via BDM (or started from
  * a different bootloader that has already performed RAM setup) or
@@ -50,31 +46,18 @@
  */
 #ifdef CONFIG_RAM
 #define CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_SYS_TEXT_BASE		0x40020000
 #define ENABLE_JFFS	0
 #else
-#define CONFIG_SYS_TEXT_BASE		0x00000000
 #define ENABLE_JFFS	1
 #endif
 
-/* Define which commands should be available at u-boot command prompt */
-
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMDLINE_EDITING
-
 #define CONFIG_MCFRTC
 #undef RTC_DEBUG
 
 /* Timer */
 #define CONFIG_MCFTMR
-#undef CONFIG_MCFPIT
 
 /* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	80000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x58000
 #define CONFIG_SYS_IMMR			CONFIG_SYS_MBAR
 
 /*
@@ -98,7 +81,6 @@
  * in u-boot command interface
  */
 
-#define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(2)
 #define CONFIG_SYS_UART2_ALT3_GPIO
 
@@ -119,9 +101,6 @@
  */
 
 #ifndef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_ENV_OFFSET		0x1FF8000
-#define CONFIG_ENV_SECT_SIZE		0x8000
-#define CONFIG_ENV_IS_IN_FLASH		1
 #else
 /*
  * environment in RAM - This is used to use a single PC-based application
@@ -129,13 +108,9 @@
  * to execute the commands from the environment. Feedback is done via setting
  * and reading memory locations.
  */
-#define CONFIG_ENV_ADDR		0x40060000
-#define CONFIG_ENV_SECT_SIZE	0x8000
-#define CONFIG_ENV_IS_IN_FLASH	1
 #endif
 
 /* here we put our FPGA configuration... */
-#define CONFIG_MISC_INIT_R	1
 
 /* Define user parameters that have to be customized most likely */
 
@@ -168,7 +143,7 @@
 #ifdef CONFIG_MONITOR_IS_IN_RAM
 #define CONFIG_BOOTCOMMAND	""	/* no autoboot in this case */
 #else
-#if CONFIG_ASTRO_V532
+#if ASTRO_V532
 #define CONFIG_BOOTCOMMAND	"protect off 0x80000 0x1ffffff;run env_check;"\
 				"run xilinxload&&run alteraload&&bootm 0x80000;"\
 				"update;reset"
@@ -178,30 +153,7 @@
 #endif
 #endif
 
-/* default bootargs that are considered during boot */
-#define CONFIG_BOOTARGS		" console=ttyS2,115200 rootfstype=romfs"\
-				" loaderversion=$loaderversion"
-
-/* default RAM address for user programs */
-#define CONFIG_SYS_LOAD_ADDR	0x20000
-
-#define CONFIG_SYS_LONGHELP
-
-#if (CONFIG_COMMANDS & CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024
-#else
-#define CONFIG_SYS_CBSIZE		256
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS		16
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
-
 #define CONFIG_FPGA_COUNT	1
-#define CONFIG_FPGA
-#define	CONFIG_FPGA_XILINX
-#define	CONFIG_FPGA_SPARTAN3
-#define CONFIG_FPGA_ALTERA
-#define CONFIG_FPGA_CYCLON2
 #define CONFIG_SYS_FPGA_PROG_FEEDBACK
 #define CONFIG_SYS_FPGA_WAIT		1000
 
@@ -209,9 +161,6 @@
 
 /* Defines memory range for test */
 
-#define CONFIG_SYS_MEMTEST_START	0x40020000
-#define CONFIG_SYS_MEMTEST_END		0x41ffffff
-
 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
@@ -282,8 +231,6 @@
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)
 
 #define CONFIG_SYS_BOOTPARAMS_LEN	(64 * 1024)
-/* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)
 
 /*
  * For booting Linux, the board info and command line data
@@ -298,16 +245,12 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	259
 #define CONFIG_SYS_FLASH_ERASE_TOUT	1000
 
-#define CONFIG_SYS_FLASH_CFI		1
-#define CONFIG_FLASH_CFI_DRIVER		1
 #define CONFIG_SYS_FLASH_SIZE		0x2000000
-#define CONFIG_SYS_FLASH_PROTECTION	1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
 #define CONFIG_SYS_FLASH_CFI_NONBLOCK	1
 
 #define LDS_BOARD_TEXT \
 	. = DEFINED(env_offset) ? env_offset : .; \
-	common/env_embedded.o       (.text*)
+	env/embedded.o(.text*)
 
 #if ENABLE_JFFS
 /* JFFS Partition offset set */
@@ -318,7 +261,6 @@
 #endif
 
 /* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE	16
 
 #define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - 8)