X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fastro_mcf5373l.h;h=36e351f3583357f47469c7264da969ad94e698aa;hb=74337aa4506c76e790ab45ad4f4ab854f25d19da;hp=3d79311d625f6e26cd15562b1fa8747362d8b164;hpb=a09fea1d28fe3c69a64bee092f5a764274d26ca2;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h
index 3d79311..36e351f 100644
--- a/include/configs/astro_mcf5373l.h
+++ b/include/configs/astro_mcf5373l.h
@@ -22,23 +22,22 @@
  * set the card type to actually compile for; either of
  * the possibilities listed below has to be used!
  */
-#define CONFIG_ASTRO_V532	1
+#define ASTRO_V532	1
 
-#if CONFIG_ASTRO_V532
+#if ASTRO_V532
 #define ASTRO_ID	0xF8
-#elif CONFIG_ASTRO_V512
+#elif ASTRO_V512
 #define ASTRO_ID	0xFA
-#elif CONFIG_ASTRO_TWIN7S2
+#elif ASTRO_TWIN7S2
 #define ASTRO_ID	0xF9
-#elif CONFIG_ASTRO_V912
+#elif ASTRO_V912
 #define ASTRO_ID	0xFC
-#elif CONFIG_ASTRO_COFDMDUOS2
+#elif ASTRO_COFDMDUOS2
 #define ASTRO_ID	0xFB
 #else
 #error No card type defined!
 #endif
 
-/* Command line configuration */
 /*
  * CONFIG_RAM defines if u-boot is loaded via BDM (or started from
  * a different bootloader that has already performed RAM setup) or
@@ -57,14 +56,8 @@
 
 /* Timer */
 #define CONFIG_MCFTMR
-#undef CONFIG_MCFPIT
 
 /* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	80000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x58000
 #define CONFIG_SYS_IMMR			CONFIG_SYS_MBAR
 
 /*
@@ -88,7 +81,6 @@
  * in u-boot command interface
  */
 
-#define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(2)
 #define CONFIG_SYS_UART2_ALT3_GPIO
 
@@ -151,7 +143,7 @@
 #ifdef CONFIG_MONITOR_IS_IN_RAM
 #define CONFIG_BOOTCOMMAND	""	/* no autoboot in this case */
 #else
-#if CONFIG_ASTRO_V532
+#if ASTRO_V532
 #define CONFIG_BOOTCOMMAND	"protect off 0x80000 0x1ffffff;run env_check;"\
 				"run xilinxload&&run alteraload&&bootm 0x80000;"\
 				"update;reset"
@@ -161,9 +153,6 @@
 #endif
 #endif
 
-/* default RAM address for user programs */
-#define CONFIG_SYS_LOAD_ADDR	0x20000
-
 #define CONFIG_FPGA_COUNT	1
 #define CONFIG_SYS_FPGA_PROG_FEEDBACK
 #define CONFIG_SYS_FPGA_WAIT		1000
@@ -172,9 +161,6 @@
 
 /* Defines memory range for test */
 
-#define CONFIG_SYS_MEMTEST_START	0x40020000
-#define CONFIG_SYS_MEMTEST_END		0x41ffffff
-
 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
@@ -245,8 +231,6 @@
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)
 
 #define CONFIG_SYS_BOOTPARAMS_LEN	(64 * 1024)
-/* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)
 
 /*
  * For booting Linux, the board info and command line data
@@ -277,7 +261,6 @@
 #endif
 
 /* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE	16
 
 #define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - 8)