X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Famcc-common.h;h=0388ffc78135a6115186fef2bc38eadb32e5d44a;hb=e16e137c377c8b96d8d91263d0b6d8470169f841;hp=580d079ed1a8a34f3f519eaf5d747b98cb03ad76;hpb=c2120fbfbc4d1f6953228f86be8bdbf38bacfdab;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h
index 580d079..0388ffc 100644
--- a/include/configs/amcc-common.h
+++ b/include/configs/amcc-common.h
@@ -10,6 +10,7 @@
 #ifndef __AMCC_COMMON_H
 #define __AMCC_COMMON_H
 
+
 #define CONFIG_SYS_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* Start of U-Boot	*/
 #define CONFIG_SYS_MONITOR_LEN		(0xFFFFFFFF - CONFIG_SYS_MONITOR_BASE + 1)
@@ -18,10 +19,11 @@
 /*
  * UART
  */
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
+#ifndef CONFIG_DM_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_serial_clock()
+#endif
 #define CONFIG_BAUDRATE		115200
 #define CONFIG_SYS_BAUDRATE_TABLE  \
     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
@@ -49,8 +51,6 @@
 /*
  * Commands
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_ASKENV
 #if defined(CONFIG_440)
 #define CONFIG_CMD_CACHE
@@ -58,23 +58,17 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_GREPENV
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SETEXPR
 
 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
 #else
@@ -90,8 +84,6 @@
 #define CONFIG_SYS_LOAD_ADDR		0x100000  /* default load address	*/
 #define CONFIG_SYS_EXTBDINFO			/* To use extended board_into (bd_t) */
 
-#define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks	*/
-
 #define CONFIG_CMDLINE_EDITING		/* add command line history	*/
 #define CONFIG_AUTO_COMPLETE		/* add autocompletion support	*/
 #define CONFIG_LOOPW			/* enable loopw command         */
@@ -105,7 +97,6 @@
 #define CONFIG_LOADS_ECHO		/* echo on for serial download	*/
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change	*/
 
-#define CONFIG_REGEX			/* Enable regular expression support */
 /*
  * BOOTP options
  */
@@ -128,14 +119,8 @@
  */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port*/
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use	*/
 #endif
 
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
 /* Update size in "reg" property of NOR FLASH device tree nodes */
 #define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE
 
@@ -257,10 +242,4 @@
 		"cp.b ${fileaddr} " __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
 	"upd=run load update\0"						\
 
-#define CONFIG_AMCC_DEF_ENV_NAND_UPD					\
-	"u-boot-nand=" __stringify(CONFIG_HOSTNAME) "/u-boot-nand.bin\0"\
-	"nload=tftp 200000 ${u-boot-nand}\0"				\
-	"nupdate=nand erase 0 100000;nand write 200000 0 100000\0"	\
-	"nupd=run nload nupdate\0"
-
 #endif /* __AMCC_COMMON_H */