X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Falpr.h;h=dfe7802119f7df75ac519b53f23f3ef3d55738c6;hb=37a3bda0c9c8a2ffbf7e2a9e121177a3385a0626;hp=e6248e9df7cc961337a7121e6ba6a696774759f6;hpb=6c869637fef31e66380f0ea1d49690a2e26ec0d7;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index e6248e9..dfe7802 100644
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -33,6 +33,9 @@
 #define CONFIG_4xx		1	    /* ... PPC4xx family	*/
 #define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_pre_init	*/
 #define CONFIG_LAST_STAGE_INIT	1	    /* call last_stage_init()	*/
+
+#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
+
 #define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
 #define CONFIG_4xx_DCACHE		/* Enable i- and d-cache	*/
 
@@ -45,7 +48,6 @@
 #define CONFIG_SYS_MONITOR_BASE	0xfffc0000	/* start of monitor		*/
 #define CONFIG_SYS_PCI_MEMBASE		0x80000000	/* mapped pci memory		*/
 #define	CONFIG_SYS_PCI_MEMSIZE		0x40000000	/* size of mapped pci memory	*/
-#define CONFIG_SYS_PERIPHERAL_BASE	0xe0000000	/* internal peripherals		*/
 #define CONFIG_SYS_ISRAM_BASE		0xc0000000	/* internal SRAM		*/
 #define CONFIG_SYS_PCI_BASE		0xd0000000	/* internal PCI regs		*/
 #define CONFIG_SYS_PCI_MEMBASE1	CONFIG_SYS_PCI_MEMBASE  + 0x10000000
@@ -66,8 +68,7 @@
 #define CONFIG_SYS_GBL_DATA_SIZE   128		    /* num bytes initial data	*/
 
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_POST_WORD_ADDR	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
 
 #define CONFIG_SYS_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
 #define CONFIG_SYS_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
@@ -75,9 +76,14 @@
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
+#define CONFIG_CONS_INDEX	2	/* Use UART1			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
+
 #undef	CONFIG_SYS_EXT_SERIAL_CLOCK
 #define CONFIG_BAUDRATE		115200
-#define	CONFIG_UART1_CONSOLE		/* define for uart1 as console	*/
 
 #define CONFIG_SYS_BAUDRATE_TABLE  \
     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
@@ -118,6 +124,7 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs	*/
@@ -231,19 +238,17 @@
  */
 #include <config_cmd_default.h>
 
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_FPGA
 #define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
 #undef CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -360,14 +365,6 @@
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */