X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Falpr.h;h=c80c76afd563ac581e7ca4a58f4d0e81a923e117;hb=0e8d158664a913392cb01fb11a948d83f72e105e;hp=c6731ba4d7c178409faac8e45b2ddfc40d5d8872;hpb=dfc8a9ee0040e53ada125a3c52f241e37f09cf28;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/alpr.h b/include/configs/alpr.h index c6731ba..c80c76a 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2006 + * (C) Copyright 2006-2008 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * See file CREDITS for list of people who contributed to this @@ -29,27 +29,28 @@ *----------------------------------------------------------------------*/ #define CONFIG_ALPR 1 /* Board is ebony */ #define CONFIG_440GX 1 /* Specifc GX support */ +#define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#define CONFIG_BOARD_RESET 1 /* call board_reset() */ -#undef CFG_DRAM_TEST /* Disable-takes long time! */ -#define CONFIG_SYS_CLK_FREQ 33333000 /* external freq to pll */ +#define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */ +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CONFIG_4xx_DCACHE /* Enable i- and d-cache */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xffe00000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ -#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CFG_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */ -#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ -#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ -#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ -#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 -#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 -#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xffe00000 /* start of FLASH */ +#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ +#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CFG_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */ +#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ +#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ +#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 +#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 +#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 #define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000) @@ -84,36 +85,23 @@ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ - +#define CFG_FLASH_CFI 1 /* The flash is CFI compatible */ +#define CONFIG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ - -#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ -#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ -#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ -/* - * The following defines are added for buggy IOP480 byte interface. - * All other boards should use the standard values (CPCI405 etc.) - */ -#define CFG_FLASH_READ0 0x0000 /* 0 is standard */ -#define CFG_FLASH_READ1 0x0001 /* 1 is standard */ -#define CFG_FLASH_READ2 0x0002 /* 2 is standard */ - +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ -#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) /*----------------------------------------------------------------------- * DDR SDRAM @@ -148,40 +136,63 @@ #define CFG_EEPROM_PAGE_WRITE_ENABLE #define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo Type \"run kernelx\" to boot the system;" \ "echo" #undef CONFIG_BOOTARGS #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ + "netdev=eth3\0" \ "hostname=alpr\0" \ + "fdt_file=alpr/alpr.dtb\0" \ + "fdt_addr=400000\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ + "nfsroot=${serverip}:${rootpath} ${init}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\ + "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \ + "mem=193M\0" \ "flash_nfs=run nfsargs addip addtty;" \ "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip addtty;" \ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/alpr/uImage\0" \ + "net_nfs_fdt=tftp 200000 ${bootfile};" \ + "tftp ${fdt_addr} ${fdt_file};" \ + "run nfsargs addip addtty;" \ + "bootm 200000 - ${fdt_addr}\0" \ + "rootpath=/opt/projects/alpr/nfs_root\0" \ + "bootfile=/alpr/uImage\0" \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ - "load=tftp 100000 /tftpboot/alpr/u-boot.bin\0" \ + "load=tftp 100000 /alpr/u-boot/u-boot.bin\0" \ "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ "cp.b 100000 fffc0000 40000;" \ "setenv filesize;saveenv\0" \ - "upd=run load;run update\0" \ + "upd=run load update\0" \ + "ethprime=ppc_4xx_eth3\0" \ + "ethact=ppc_4xx_eth3\0" \ + "autoload=no\0" \ + "ipconfig=dhcp;setenv serverip 11.0.0.152\0" \ + "load_fpga=fpga load 0 ffe00000 10dd9a\0" \ + "mtdargs=setenv bootargs root=/dev/mtdblock6 rw " \ + "rootfstype=jffs2 init=/sbin/init\0" \ + "kernel1_mtd=nand read 200000 0 200000;run mtdargs addip addtty"\ + ";bootm 200000\0" \ + "kernel2_mtd=nand read 200000 200000 200000;run mtdargs addip " \ + "addtty;bootm 200000\0" \ + "kernel1=setenv actkernel 'kernel1';run load_fpga " \ + "kernel1_mtd\0" \ + "kernel2=setenv actkernel 'kernel2';run load_fpga " \ + "kernel2_mtd\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CONFIG_BOOTCOMMAND "run kernel2" + +#define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */ #define CONFIG_BAUDRATE 115200 @@ -192,38 +203,50 @@ #define CONFIG_NET_MULTI 1 #define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */ #define CONFIG_PHY1_ADDR 0x03 /* dummy setting, no EMAC1 used */ -#define CONFIG_PHY2_ADDR 0x00 /* test-only: will be changed */ -#define CONFIG_PHY3_ADDR 0x01 /* PHY address for EMAC3 */ +#define CONFIG_PHY2_ADDR 0x01 /* PHY address for EMAC2 */ +#define CONFIG_PHY3_ADDR 0x02 /* PHY address for EMAC3 */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 #define CONFIG_HAS_ETH3 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CONFIG_88E1111_CLK_DELAY 1 /* set CLK delay on ALPR */ +#define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_ASKENV | \ - CFG_CMD_DHCP | \ - CFG_CMD_DIAG | \ - CFG_CMD_EEPROM | \ - CFG_CMD_ELF | \ - CFG_CMD_I2C | \ - CFG_CMD_IRQ | \ - CFG_CMD_MII | \ - CFG_CMD_NET | \ - CFG_CMD_NFS | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_FPGA | \ - CFG_CMD_NAND | \ - CFG_CMD_REGINFO) - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FPGA +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + #undef CONFIG_WATCHDOG /* watchdog disabled */ @@ -232,7 +255,7 @@ */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -241,6 +264,7 @@ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_ALT_MEMTEST 1 /* Enable more extensive memtest*/ #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ @@ -251,9 +275,11 @@ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ /*----------------------------------------------------------------------- * PCI stuff @@ -264,10 +290,9 @@ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ -#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ +#define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/ /* Board-specific PCI */ -#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ #define CFG_PCI_TARGET_INIT /* let board init pci target */ #define CFG_PCI_MASTER_INIT @@ -276,11 +301,12 @@ /*----------------------------------------------------------------------- * FPGA stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_FPGA CFG_ALTERA_CYCLON2 -#undef CFG_FPGA_CHECK_CTRLC -#undef CFG_FPGA_PROG_FEEDBACK + *-----------------------------------------------------------------------*/ +#define CONFIG_FPGA +#define CONFIG_FPGA_ALTERA +#define CONFIG_FPGA_CYCLON2 +#define CFG_FPGA_CHECK_CTRLC +#define CFG_FPGA_PROG_FEEDBACK #define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in Reihe geschaltet -> sollte gehen, aufpassen mit Datasize ist jetzt @@ -299,9 +325,18 @@ #define CFG_GPIO_SEL_AVR 15 /* cpu output */ #define CFG_GPIO_PROG_EN 23 /* cpu output */ -/* +/*----------------------------------------------------------------------- + * Definitions for GPIO setup + *-----------------------------------------------------------------------*/ +#define CFG_GPIO_SHUTDOWN (0x80000000 >> 6) +#define CFG_GPIO_SSD_EMPTY (0x80000000 >> 9) +#define CFG_GPIO_EREADY (0x80000000 >> 26) +#define CFG_GPIO_REV0 (0x80000000 >> 14) +#define CFG_GPIO_REV1 (0x80000000 >> 15) + +/*----------------------------------------------------------------------- * NAND-FLASH stuff - */ + *-----------------------------------------------------------------------*/ #define CFG_MAX_NAND_DEVICE 4 #define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE #define CFG_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */ @@ -320,7 +355,7 @@ /* Memory Bank 1 (NAND-FLASH) initialization */ #define CFG_EBC_PB1AP 0x01840380 /* TWT=3 */ -#define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x1A000) /* BS=1MB,BU=R/W,BW=16bit */ +#define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */ /* * For booting Linux, the board info and command line data @@ -328,14 +363,6 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Internal Definitions @@ -345,8 +372,13 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + #endif /* __CONFIG_H */