X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Falpr.h;h=0f125dce0958e17279c6ccf2c7f4392b983d96eb;hb=6eed3786c68c8a49d2986ac4f9f6e3071b769d41;hp=86b874cfe27670dc5d735b839602a9fe41c805a5;hpb=3765b3e7bd0f8e46914d417f29cbcb0c72b1acf7;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index 86b874c..0f125dc 100644
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -14,7 +14,6 @@
 #define CONFIG_ALPR		1	    /* Board is ebony		*/
 #define CONFIG_440GX		1	    /* Specifc GX support	*/
 #define CONFIG_440		1	    /* ... PPC440 family	*/
-#define CONFIG_4xx		1	    /* ... PPC4xx family	*/
 #define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_pre_init	*/
 #define CONFIG_LAST_STAGE_INIT	1	    /* call last_stage_init()	*/
 
@@ -148,7 +147,7 @@
 	"flash_self=run ramargs addip addtty;"				\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
+		"bootm\0"						\
 	"net_nfs_fdt=tftp 200000 ${bootfile};"				\
 		"tftp ${fdt_addr} ${fdt_file};"				\
 		"run nfsargs addip addtty;"				\
@@ -223,12 +222,12 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_FPGA
+#define CONFIG_CMD_FPGA_LOADMK
 #define CONFIG_CMD_I2C
 #undef CONFIG_CMD_LOADB
 #undef CONFIG_CMD_LOADS
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
 #undef CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
 
@@ -238,7 +237,6 @@
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
@@ -255,8 +253,6 @@
 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
 #define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
 
-#define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */
-
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_LOOPW            1       /* enable loopw command         */
 #define CONFIG_MX_CYCLIC	1       /* enable mdc/mwc commands      */
@@ -327,6 +323,8 @@
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2,	\
 				  CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 }
 #define CONFIG_SYS_NAND_QUIET_TEST	1	/* don't warn upon unknown NAND flash	*/
+#define CONFIG_SYS_NAND_MAX_OOBFREE	2
+#define CONFIG_SYS_NAND_MAX_ECCPOS	56
 
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
@@ -350,7 +348,6 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 
 /* pass open firmware flat tree */