X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Factux2.h;h=d2cc26c2a24b4e075a6b0b3d62f5b56eeb0e6c75;hb=4c25761337570e63e9e2631a81de221e692251e3;hp=4c579ebe2f78977c5502cb2f1143157ba80b0c03;hpb=6c6e042ab3bbfb5428e4cdeb38fa27728c63afdd;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/actux2.h b/include/configs/actux2.h
index 4c579eb..d2cc26c 100644
--- a/include/configs/actux2.h
+++ b/include/configs/actux2.h
@@ -29,6 +29,8 @@
 #define CONFIG_IXP425			1
 #define CONFIG_ACTUX2			1
 
+#define	CONFIG_MACH_TYPE		1480
+
 #define CONFIG_DISPLAY_CPUINFO		1
 #define CONFIG_DISPLAY_BOARDINFO	1
 
@@ -37,16 +39,14 @@
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_BOOTDELAY		5
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_BOARD_EARLY_INIT_F	1
+#define CONFIG_SYS_LDSCRIPT	"board/actux2/u-boot.lds"
 
 /***************************************************************
  * U-boot generic defines start here.
  ***************************************************************/
-#undef CONFIG_USE_IRQ
-
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN			(CONFIG_ENV_SIZE + 128*1024)
-/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE		128
 
 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
@@ -86,10 +86,9 @@
 #define CONFIG_SYS_MEMTEST_START		0x00400000
 #define CONFIG_SYS_MEMTEST_END			0x00800000
 
-/* everything, incl board info, in Hz */
-#undef  CONFIG_SYS_CLKS_IN_HZ
-/* spec says 66.666 MHz, but it appears to be 33 */
-#define CONFIG_SYS_HZ				3333333
+/* timer clock - 2* OSC_IN system clock */
+#define CONFIG_IXP425_TIMER_CLK                 66666666
+#define CONFIG_SYS_HZ				1000
 
 /* default load address */
 #define CONFIG_SYS_LOAD_ADDR			0x00010000
@@ -99,23 +98,13 @@
 					  115200, 230400 }
 #define CONFIG_SERIAL_RTS_ACTIVE	1
 
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE		(128*1024)	/* regular stack */
-#ifdef CONFIG_USE_IRQ
-# define CONFIG_STACKSIZE_IRQ		(4*1024)	/* IRQ stack */
-# define CONFIG_STACKSIZE_FIQ		(4*1024)	/* FIQ stack */
-#endif
-
 /* Expansion bus settings */
 #define CONFIG_SYS_EXP_CS0			0xbd113042
 
 /* SDRAM settings */
 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM_1			0x00000000
-#define CONFIG_SYS_DRAM_BASE			0x00000000
+#define CONFIG_SYS_SDRAM_BASE			0x00000000
 
 /* 16MB SDRAM */
 #define CONFIG_SYS_SDR_CONFIG			0x3A
@@ -125,6 +114,7 @@
 #define CONFIG_SYS_DRAM_SIZE			0x01000000
 
 /* FLASH organization */
+#define CONFIG_SYS_TEXT_BASE		0x50000000
 #define CONFIG_SYS_MAX_FLASH_BANKS		1
 /* max number of sectors on one chip */
 #define CONFIG_SYS_MAX_FLASH_SECT		140
@@ -134,6 +124,7 @@
 #define CONFIG_SYS_FLASH_BASE			PHYS_FLASH_1
 #define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
 #define CONFIG_SYS_MONITOR_LEN			(256 << 10)
+#define CONFIG_BOARD_SIZE_LIMIT			262144
 
 /* Use common CFI driver */
 #define CONFIG_SYS_FLASH_CFI
@@ -148,11 +139,15 @@
 
 /* include IXP4xx NPE support */
 #define CONFIG_IXP4XX_NPE		1
-#define CONFIG_NET_MULTI		1
 /* NPE0 PHY address */
 #define	CONFIG_PHY_ADDR			0x00
 /* MII PHY management */
 #define CONFIG_MII			1
+/* fixed-speed switch without standard PHY registers on MII */
+#define CONFIG_MII_NPE0_FIXEDLINK       1
+#define CONFIG_MII_NPE0_SPEED           100
+#define CONFIG_MII_NPE0_FULLDUPLEX      1
+
 /* Number of ethernet rx buffers & descriptors */
 #define CONFIG_SYS_RX_ETH_BUFFER		16
 #define CONFIG_RESET_PHY_R		1
@@ -187,13 +182,15 @@
 	"npe_ucode=50040000\0"						\
 	"mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \
 	"kerneladdr=50050000\0"						\
+	"kernelfile=actux2/uImage\0"					\
+	"rootfile=actux2/rootfs\0"					\
 	"rootaddr=50170000\0"						\
 	"loadaddr=10000\0"						\
 	"updateboot_ser=mw.b 10000 ff 40000;"				\
 	" loady ${loadaddr};"						\
 	" run eraseboot writeboot\0"					\
 	"updateboot_net=mw.b 10000 ff 40000;"				\
-	" tftp ${loadaddr} u-boot.bin;"					\
+	" tftp ${loadaddr} actux2/u-boot.bin;"				\
 	" run eraseboot writeboot\0"					\
 	"eraseboot=protect off 50000000 50003fff;"			\
 	" protect off 50006000 5003ffff;"				\
@@ -201,8 +198,9 @@
 	" erase 50006000 5003ffff\0"					\
 	"writeboot=cp.b 10000 50000000 4000;"				\
 	" cp.b 16000 50006000 3a000\0"					\
-	"eraseenv=protect off 50004000 50005fff;"			\
-	" erase 50004000 50005fff\0"					\
+	"updateucode=loady;"						\
+	" era ${npe_ucode} +${filesize};"				\
+	" cp.b ${loadaddr} ${npe_ucode} ${filesize}\0"			\
 	"updateroot=tftp ${loadaddr} ${rootfile};"			\
 	" era ${rootaddr} +${filesize};"				\
 	" cp.b ${loadaddr} ${rootaddr} ${filesize}\0"			\
@@ -221,4 +219,8 @@
 	" tftpboot ${loadaddr} ${kernelfile};"				\
 	" bootm\0"
 
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_INIT_SP_ADDR						\
+	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */