X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fa4m072.h;h=6a26269807e3a09343c206982e150889c75dfcd5;hb=75eb9976b78ace0e667c1f5faf367acfaed141df;hp=0ff5164ce6897e7e6236aff77a588cba944190f1;hpb=09f3ca3dd53b671b009ddc4e1dad669c280094f0;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h
index 0ff5164..6a26269 100644
--- a/include/configs/a4m072.h
+++ b/include/configs/a4m072.h
@@ -19,7 +19,6 @@
 #define CONFIG_MPC5200		1	/* This is a MPC5200 CPU */
 #define CONFIG_A4M072		1	/* ... on A4M072 board */
 #define CONFIG_MPC5200_DDR	1	/* ... use DDR RAM */
-#define CONFIG_DISPLAY_BOARDINFO
 
 #define CONFIG_SYS_TEXT_BASE	0xFE000000
 
@@ -33,10 +32,8 @@
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
-#define CONFIG_BAUDRATE		9600	/* ... at 9600 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 /* define to enable silent console */
-#define CONFIG_SILENT_CONSOLE
 #define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device */
 
 /*
@@ -44,10 +41,8 @@
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  */
-#define CONFIG_PCI
 
 #if defined(CONFIG_PCI)
-#define CONFIG_PCI_PNP		1
 #define CONFIG_PCI_SCAN_SHOW	1
 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1
 
@@ -64,13 +59,8 @@
 
 #undef CONFIG_EEPRO100
 
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
 /* USB */
 #define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_STORAGE
 #define CONFIG_SYS_OHCI_BE_CONTROLLER
 #undef CONFIG_SYS_USB_OHCI_BOARD_INIT
 #define CONFIG_SYS_USB_OHCI_CPU_INIT	1
@@ -88,20 +78,9 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DISPLAY
 
 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
@@ -115,7 +94,6 @@
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY	2	/* autoboot after 2 seconds */
 
 #define CONFIG_SYS_AUTOLOAD	"n"
 
@@ -166,25 +144,6 @@
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
 
 /*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C			1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x52	/* 1010010x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-#define CONFIG_SYS_EEPROM_WREN			1
-#define CONFIG_SYS_EEPROM_WP			GPIO_PSC2_4
-
-/*
  * Flash configuration
  */
 #define CONFIG_SYS_FLASH_BASE		0xFE000000
@@ -227,7 +186,6 @@
 #define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
 #define CONFIG_SYS_INIT_RAM_SIZE		MPC5XXX_SRAM_SIZE	/* Size of used area in DPRAM */
 
-
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
@@ -260,7 +218,6 @@
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_CMDLINE_EDITING	1
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
 #if defined(CONFIG_CMD_KGDB)
@@ -282,7 +239,6 @@
 #  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
-
 /*
  * Various low-level settings
  */
@@ -354,9 +310,6 @@
  * Open firmware flat tree support
  *-----------------------------------------------------------------------
  */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)