X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FWUH405.h;h=504ad96b038cee7686b561d9f6adaddcda6dda82;hb=544aa66a6695790227613bf32bdf672143d5a1ad;hp=be9ac6261c194d9d201254038e0ba3c32a735091;hpb=fd4e49c18901a50b1648235f26da1e8caa0f8764;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h
index be9ac62..504ad96 100644
--- a/include/configs/WUH405.h
+++ b/include/configs/WUH405.h
@@ -38,6 +38,8 @@
 #define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_WUH405		1	/* ...on a WUH405 board		*/
 
+#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
 
@@ -58,7 +60,6 @@
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
-#define CONFIG_NET_MULTI
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
@@ -122,9 +123,14 @@
 #define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
+#define CONFIG_CONS_INDEX	2	/* Use UART1			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
+
 #undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
 #define CONFIG_SYS_BASE_BAUD	    691200
-#define	CONFIG_UART1_CONSOLE		/* define for uart1 as console	*/
 
 /* The following table includes the supported baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE	\
@@ -314,10 +320,9 @@
 #define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
 #define CONFIG_SYS_OCM_DATA_SIZE	0x1000
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM	*/
+#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
 
-#define CONFIG_SYS_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -332,25 +337,17 @@
  * GPIO0[28-29] - UART1 data signal input/output
  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
  */
-#define CONFIG_SYS_GPIO0_OSRH		0x40000550
-#define CONFIG_SYS_GPIO0_OSRL		0x00000110
-#define CONFIG_SYS_GPIO0_ISR1H		0x00000000
-#define CONFIG_SYS_GPIO0_ISR1L		0x15555445
-#define CONFIG_SYS_GPIO0_TSRH		0x00000000
+#define CONFIG_SYS_GPIO0_OSRL		0x40000550
+#define CONFIG_SYS_GPIO0_OSRH		0x00000110
+#define CONFIG_SYS_GPIO0_ISR1L		0x00000000
+#define CONFIG_SYS_GPIO0_ISR1H		0x15555445
 #define CONFIG_SYS_GPIO0_TSRL		0x00000000
+#define CONFIG_SYS_GPIO0_TSRH		0x00000000
 #define CONFIG_SYS_GPIO0_TCR		0xF7FE0014
 
 #define CONFIG_SYS_DUART_RST		(0x80000000 >> 14)
 
 /*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-/*
  * Default speed selection (cpu_plb_opb_ebc) in mhz.
  * This value will be set if iic boot eprom is disabled.
  */