X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FW7OLMC.h;h=bb6b6b9d26c1bce7bbe9bc4ec981f08cbefb729c;hb=29f8f58ff40c67f7f2e11afd1715173094e52ac2;hp=b5610c9506fc47d40c1ed2106b4f3c7256d1c9f1;hpb=db2f721ffcf9693086a7e5c6c7015f2019e7f52e;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h
index b5610c9..bb6b6b9 100644
--- a/include/configs/W7OLMC.h
+++ b/include/configs/W7OLMC.h
@@ -38,7 +38,8 @@
 #define CONFIG_W7O		1		/* ...on a Wave 7 Optics board	*/
 #define CONFIG_W7OLMC		1		/* ...specifically an LMC	*/
 
-#define CONFIG_BOARD_PRE_INIT	1		/* Call board_pre_init	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f	*/
+#define	CONFIG_MISC_INIT_F	1		/* and misc_init_f()		*/
 
 #define CONFIG_SYS_CLK_FREQ	33333333	/* external frequency to pll	*/
 
@@ -69,13 +70,31 @@
 
 #define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
 
-#define CONFIG_COMMANDS		\
-	(CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | CFG_CMD_ASKENV | \
-	 CFG_CMD_DHCP | CFG_CMD_BEDBUG | CFG_CMD_DATE | CFG_CMD_I2C | \
-	 CFG_CMD_EEPROM | CFG_CMD_ELF | CFG_CMD_BSP | CFG_CMD_REGINFO)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_REGINFO
 
 #undef CONFIG_WATCHDOG				/* watchdog disabled		*/
 #define CONFIG_HW_WATCHDOG			/* HW Watchdog, board specific	*/
@@ -91,7 +110,7 @@
 #ifdef  CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2     "> "
 #endif
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
@@ -135,10 +154,10 @@
 #define CFG_PCI_SUBSYS_DEVICEID 0x0156		/* PCI Device ID: 405GP		*/
 #define CFG_PCI_PTM1LA		0x00000000	/* point to sdram		*/
 #define CFG_PCI_PTM1MS		0x80000001	/* 2GB, enable hard-wired to 1	*/
-#define CFG_PCI_PTM1PCI 	0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA		0x00000000	/* disabled		*/
-#define CFG_PCI_PTM2MS		0x00000000	/* disabled		*/
-#define CFG_PCI_PTM2PCI 	0x00000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM1PCI		0x00000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM2LA		0x00000000	/* disabled			*/
+#define CFG_PCI_PTM2MS		0x00000000	/* disabled			*/
+#define CFG_PCI_PTM2PCI		0x00000000      /* Host: use this pci address   */
 
 /*-----------------------------------------------------------------------
  * Set up values for external bus controller
@@ -271,15 +290,6 @@
  */
 #define SPD_EEPROM_ADDRESS      0x50	/* XXX conflicting address!!! XXX */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		8192		/* For IBM 405 CPUs			*/
-#define CFG_CACHELINE_SIZE	32		/* ...		*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5		/* log base 2 of the above val. */
-#endif
-
 /*
  * Init Memory Controller:
  */
@@ -308,7 +318,7 @@
 #define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM		0x02		/* Software reboot		*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use	*/
 #endif
@@ -323,4 +333,3 @@
 #define CONFIG_FPGAS_BANK_SIZE	0x00100000L	/* FPGAs' mmap bank size	*/
 
 #endif	/* __CONFIG_H */
-