X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FW7OLMC.h;h=9eacd82323afd2ac745be6bdf69642683a4e64d1;hb=d98b0523cfaaedeecb263b15c121c0727b0d80b9;hp=e546369c994777c3f4330f814669014fceca14fe;hpb=6d0f6bcf337c5261c08fabe12982178c2c489d76;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h
index e546369..9eacd82 100644
--- a/include/configs/W7OLMC.h
+++ b/include/configs/W7OLMC.h
@@ -38,8 +38,11 @@
 #define CONFIG_W7O		1		/* ...on a Wave 7 Optics board	*/
 #define CONFIG_W7OLMC		1		/* ...specifically an LMC	*/
 
+#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
+
 #define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f	*/
 #define	CONFIG_MISC_INIT_F	1		/* and misc_init_f()		*/
+#define	CONFIG_MISC_INIT_R	1		/* and misc_init_r()		*/
 
 #define CONFIG_SYS_CLK_FREQ	33333333	/* external frequency to pll	*/
 
@@ -65,8 +68,10 @@
 #define CONFIG_LOADS_ECHO	1		/* echo on for serial download	*/
 #undef CONFIG_SYS_LOADS_BAUD_CHANGE			/* disallow baudrate change	*/
 
+#define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII		1		/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0		/* PHY address			*/
+#define CONFIG_NET_MULTI
 
 #define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
 
@@ -122,6 +127,12 @@
 #define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on		*/
 #define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/
 
+#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
+
 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK			/* external serial clock */
 #define CONFIG_SYS_405_UART_ERRATA_59			/* 405GP/CR Rev. D silicon */
 #define CONFIG_SYS_BASE_BAUD		384000
@@ -130,8 +141,6 @@
 /* The following table includes the supported baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE	{9600}
 
-#define CONFIG_SYS_CLKS_IN_HZ		1		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address		*/
 #define CONFIG_SYS_EXTBDINFO		1		/* use extended board_info (bd_t) */
 
@@ -207,9 +216,9 @@
 #define CONFIG_SYS_EBC_PB5CR   0xFD21A000
 
 /* bank 6 is unused */
-/* pb6ap = 0 */
+/* PB6AP = 0 */
 #define CONFIG_SYS_EBC_PB6AP   0x00000000
-/* pb6cr = 0 */
+/* PB6CR = 0 */
 #define CONFIG_SYS_EBC_PB6CR   0x00000000
 
 /* bank 7 is LED register */
@@ -272,6 +281,7 @@
  * I2C EEPROM (CAT24WC08) for environment
  */
 #define CONFIG_HARD_I2C			/* I2c with hardware support */
+#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
@@ -308,15 +318,6 @@
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM		0x02		/* Software reboot		*/
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use	*/