X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FVCMA9.h;h=aeb649e190f1313252f201027b0a23fac3b6f19e;hb=0e8d158664a913392cb01fb11a948d83f72e105e;hp=c0103fc335a4544ede765490337439895233d833;hpb=48b42616e928ce6eacfe20276a1614e2b27ac4b5;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h index c0103fc..aeb649e 100644 --- a/include/configs/VCMA9.h +++ b/include/configs/VCMA9.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2002 + * (C) Copyright 2002, 2003 * Sysgo Real-Time Solutions, GmbH * Marius Groeger * Gary Jennejohn @@ -30,18 +30,13 @@ #define __CONFIG_H /* - * If we are developing, we might want to start armboot from ram - * so we MUST NOT initialize critical regs like mem-timing ... - */ -#define CONFIG_INIT_CRITICAL /* undef for developing */ - -/* * High Level Configuration Options * (easy to change) */ #define CONFIG_ARM920T 1 /* This is an ARM920T Core */ #define CONFIG_S3C2410 1 /* in a SAMSUNG S3C2410 SoC */ #define CONFIG_VCMA9 1 /* on a MPL VCMA9 Board */ +#define LITTLEENDIAN 1 /* used by usb_ohci.c */ /* input clock of PLL */ #define CONFIG_SYS_CLK_FREQ 12000000/* VCMA9 has 12MHz input clock */ @@ -49,28 +44,37 @@ #define USE_920T_MMU 1 #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ #define CONFIG_SETUP_MEMORY_TAGS 1 #define CONFIG_INITRD_TAG 1 -/*********************************************************** - * Command definition - ***********************************************************/ -#define CONFIG_COMMANDS \ - (CONFIG_CMD_DFL | \ - CFG_CMD_CACHE | \ - /*CFG_CMD_JFFS2 |*/ \ - /*CFG_CMD_NAND |*/ \ - CFG_CMD_EEPROM | \ - CFG_CMD_I2C | \ - /*CFG_CMD_USB |*/ \ - CFG_CMD_REGINFO | \ - CFG_CMD_DATE | \ - CFG_CMD_ELF | \ - CFG_CMD_BSP) - -/* this must be included after the definiton of CONFIG_COMMANDS */ -#include + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_USB +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_FAT +#define CONFIG_CMD_DATE +#define CONFIG_CMD_ELF +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_BSP + #define CFG_HUSH_PARSER #define CFG_PROMPT_HUSH_PS2 "> " @@ -80,14 +84,14 @@ * address 0x50 with 16bit addressing ***********************************************************/ #define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CFG_I2C_SPEED 100000 /* I2C speed */ -#define CFG_I2C_SLAVE 0x7F /* I2C slave addr */ +#define CFG_I2C_SPEED 100000 /* I2C speed */ +#define CFG_I2C_SLAVE 0x7F /* I2C slave addr */ #define CFG_I2C_EEPROM_ADDR 0x50 #define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CFG_ENV_OFFSET 0x000 /* environment starts at offset 0 */ -#define CFG_ENV_SIZE 0x800 /* 2KB should be more than enough */ +#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CONFIG_ENV_OFFSET 0x000 /* environment starts at offset 0 */ +#define CONFIG_ENV_SIZE 0x800 /* 2KB should be more than enough */ #undef CFG_I2C_EEPROM_ADDR_OVERFLOW #define CFG_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes page write mode on 24C256 */ @@ -96,17 +100,18 @@ /* * Size of malloc() pool */ -#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024) +/*#define CONFIG_MALLOC_SIZE (CONFIG_ENV_SIZE + 128*1024)*/ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CFG_MONITOR_LEN (256 * 1024) -#define CFG_MALLOC_LEN (128 * 1024) +#define CFG_MALLOC_LEN (1024 * 1024) /* BUNZIP2 needs a lot of RAM */ /* * Hardware drivers */ #define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ #define CS8900_BASE 0x20000300 -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ #define CONFIG_DRIVER_S3C24X0_I2C 1 /* we use the buildin I2C controller */ @@ -118,14 +123,13 @@ /************************************************************ * USB support ************************************************************/ -#if 0 -#define CONFIG_USB_OHCI -#define CONFIG_USB_KEYBOARD -#define CONFIG_USB_STORAGE +#define CONFIG_USB_OHCI 1 +#define CONFIG_USB_KEYBOARD 1 +#define CONFIG_USB_STORAGE 1 +#define CONFIG_DOS_PARTITION 1 /* Enable needed helper functions */ #define CFG_DEVICE_DEREGISTER /* needs device_deregister */ -#endif /************************************************************ * RTC @@ -138,12 +142,16 @@ #define CONFIG_BAUDRATE 9600 -#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTDELAY 5 +/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */ +/* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */ + #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_IPADDR 10.0.0.110 #define CONFIG_SERVERIP 10.0.0.1 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ /* what's this ? it's not used anywhere */ #define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */ @@ -160,9 +168,10 @@ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_MEMTEST_START 0x30000000 /* memtest works on */ -#define CFG_MEMTEST_END 0x33F80000 /* 63.5 MB in DRAM */ +#define CFG_MEMTEST_END 0x30F80000 /* 15.5 MB in DRAM */ + #define CFG_ALT_MEMTEST -#define CFG_LOAD_ADDR 0x33000000 /* default load address */ +#define CFG_LOAD_ADDR 0x30800000 /* default load address */ #undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ @@ -174,6 +183,9 @@ /* valid baudrates */ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +/* support BZIP2 compression */ +#define CONFIG_BZIP2 1 + /************************************************************ * Ident ************************************************************/ @@ -197,8 +209,6 @@ */ #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ #define PHYS_SDRAM_1 0x30000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ - #define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ #define CFG_FLASH_BASE PHYS_FLASH_1 @@ -216,12 +226,12 @@ #ifdef CONFIG_AMD_LV800 #define PHYS_FLASH_SIZE 0x00100000 /* 1MB */ #define CFG_MAX_FLASH_SECT (19) /* max number of sectors on one chip */ -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x0F0000) /* addr of environment */ +#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x0F0000) /* addr of environment */ #endif #ifdef CONFIG_AMD_LV400 #define PHYS_FLASH_SIZE 0x00080000 /* 512KB */ #define CFG_MAX_FLASH_SECT (11) /* max number of sectors on one chip */ -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x070000) /* addr of environment */ +#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x070000) /* addr of environment */ #endif /* timeout values are in ticks */ @@ -229,8 +239,8 @@ #define CFG_FLASH_WRITE_TOUT (5*CFG_HZ) /* Timeout for Flash Write */ #if 0 -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ #endif @@ -242,8 +252,9 @@ /*----------------------------------------------------------------------- * NAND flash settings */ -#if (CONFIG_COMMANDS & CFG_CMD_NAND) +#if defined(CONFIG_CMD_NAND) +#define CONFIG_NAND_LEGACY #define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ #define SECTORSIZE 512 @@ -251,7 +262,7 @@ #define ADDR_PAGE 2 #define ADDR_COLUMN_PAGE 3 -#define NAND_ChipID_UNKNOWN 0x00 +#define NAND_ChipID_UNKNOWN 0x00 #define NAND_MAX_FLOORS 1 #define NAND_MAX_CHIPS 1 @@ -275,6 +286,6 @@ #define CONFIG_MTD_NAND_VERIFY_WRITE 1 #define CONFIG_MTD_NAND_ECC_JFFS2 1 -#endif /* CONFIG_COMMANDS & CFG_CMD_NAND */ +#endif #endif /* __CONFIG_H */