X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FUCP1020.h;h=8579290e81d31bf9c9036cb350f8767ba1ea2311;hb=235c5b8315c6a9eb566fd3d99a098cc6db869fc5;hp=f32fb4d0417b865bd3028dc52e451781dd975e12;hpb=66e399b68d20d96a90ba391d75c2290bd63bf4a5;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h
index f32fb4d..8579290 100644
--- a/include/configs/UCP1020.h
+++ b/include/configs/UCP1020.h
@@ -14,7 +14,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_FSL_ELBC
 #define CONFIG_PCIE1	/* PCIE controller 1 (slot 1) */
 #define CONFIG_PCIE2	/* PCIE controller 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
@@ -130,35 +129,12 @@
 
 #define CONFIG_HWCONFIG
 
-#define CONFIG_DTT_ADM1021	1	/* ADM1021 temp sensor support	*/
-#define CONFIG_SYS_DTT_BUS_NUM	1	/* The I2C bus for DTT		*/
-#define CONFIG_DTT_SENSORS	{ 0, 1 }	/* Sensor index	*/
-/*
- * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
- * there will be one entry in this array for each two (dummy) sensors in
- * CONFIG_DTT_SENSORS.
- *
- * For uCP1020 module:
- * - only one ADM1021/NCT72
- * - i2c addr 0x41
- * - conversion rate 0x02 = 0.25 conversions/second
- * - ALERT output disabled
- * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
- * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
- */
-#define CONFIG_SYS_DTT_ADM1021	{ { CONFIG_SYS_I2C_NCT72_ADDR, \
-					 0x02, 0, 1, 0, 85, 1, 0, 85} }
-
-#define CONFIG_CMD_DTT
-
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_L2_CACHE
 #define CONFIG_BTB
 
-#define CONFIG_BOARD_EARLY_INIT_F	/* Call board_pre_init */
-
 #define CONFIG_ENABLE_36BIT_PHYS
 
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
@@ -335,7 +311,7 @@
 #define CONFIG_SYS_SPD_BUS_NUM		1 /* For rom_loc and flash bank */
 
 #define CONFIG_RTC_DS1337
-#define CONFIG_SYS_RTC_DS1337_NOOSC
+#define CONFIG_RTC_DS1337_NOOSC
 #define CONFIG_SYS_I2C_RTC_ADDR		0x68
 #define CONFIG_SYS_I2C_PCA9557_ADDR	0x18
 #define CONFIG_SYS_I2C_NCT72_ADDR	0x4C
@@ -380,7 +356,6 @@
 #define CONFIG_CMD_PCI
 
 #define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #endif /* CONFIG_PCI */
 
 /*
@@ -446,12 +421,7 @@
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_CRAMFS
 
 /*
  * USB
@@ -459,11 +429,9 @@
 #define CONFIG_HAS_FSL_DR_USB
 
 #if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #endif
@@ -476,11 +444,6 @@
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #define CONFIG_MMC_SPI
 #define CONFIG_CMD_MMC_SPI
-#define CONFIG_GENERIC_MMC
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA)
-#define CONFIG_DOS_PARTITION
 #endif
 
 /* Misc Extra Settings */
@@ -564,8 +527,6 @@
 
 #define CONFIG_BOOTARGS	/* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE	115200
-
 #if defined(CONFIG_DONGLE)
 
 #define	CONFIG_EXTRA_ENV_SETTINGS					\