X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FTotal5200.h;h=2507d77776547beb31194a4085a95f08f4289604;hb=cfd60441d8360cb9ffa315ecf3a2aef9bc134905;hp=d8686dd39c0072b5b6ce1f06c4db764578abf112;hpb=d7d5204ce2e0985ff2dfdf3a6b5b6a526cdb1c1e;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h
index d8686dd..2507d77 100644
--- a/include/configs/Total5200.h
+++ b/include/configs/Total5200.h
@@ -48,11 +48,6 @@
 #define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH  */
 #define BOOTFLAG_WARM		0x02	/* Software reboot	     */
 
-#define CFG_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
 /*
  * Serial console configuration
  */
@@ -63,7 +58,6 @@
 /*
  * Video console
  */
-#if 1
 #define CONFIG_VIDEO
 #define CONFIG_VIDEO_SED13806
 #define CONFIG_VIDEO_SED13806_16BPP
@@ -76,10 +70,6 @@
 #define CONFIG_VIDEO_SW_CURSOR
 #define CONFIG_SPLASH_SCREEN
 
-#define ADD_VIDEO_CMD	CFG_CMD_BMP
-#else
-#define ADD_VIDEO_CMD	0
-#endif
 
 #ifdef CONFIG_MPC5200	/* MGT5100 PCI is not supported yet. */
 /*
@@ -90,6 +80,7 @@
 #define CONFIG_PCI		1
 #define CONFIG_PCI_PNP		1
 #define CONFIG_PCI_SCAN_SHOW	1
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1
 
 #define CONFIG_PCI_MEM_BUS	0x40000000
 #define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
@@ -105,12 +96,9 @@
 #define CFG_RX_ETH_BUFFER	8  /* use 8 rx buffer on eepro100  */
 #define CONFIG_NS8382X		1
 
-#define ADD_PCI_CMD 		CFG_CMD_PCI
-
 #else	/* MGT5100 */
 
 #define CONFIG_MII		1
-#define ADD_PCI_CMD		0  /* no CFG_CMD_PCI */
 
 #endif
 
@@ -119,29 +107,36 @@
 #define CONFIG_DOS_PARTITION
 
 /* USB */
-#if 1
 #define CONFIG_USB_OHCI
-#define ADD_USB_CMD             CFG_CMD_USB | CFG_CMD_FAT
 #define CONFIG_USB_STORAGE
-#else
-#define ADD_USB_CMD             0
-#endif
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
 
 /*
- * Supported commands
+ * Command line configuration.
  */
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL	| \
-				 CFG_CMD_PING	| \
-				 CFG_CMD_I2C	| \
-				 CFG_CMD_EEPROM	| \
-				 CFG_CMD_FAT	| \
-				 CFG_CMD_IDE	| \
-				 ADD_VIDEO_CMD  | \
-				 ADD_PCI_CMD	| \
-				 ADD_USB_CMD)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#include <config_cmd_default.h>
+
+#if defined(CONFIG_MPC5200)
+    #define CONFIG_CMD_PCI
+#endif
+
+#define CONFIG_CMD_BMP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
 
 #if (TEXT_BASE == 0xFE000000)		/* Boot low */
 #   define CFG_LOWBOOT		1
@@ -155,7 +150,7 @@
 #define CONFIG_PREBOOT	\
 	"setenv stdout serial;setenv stderr serial;" \
 	"echo;" \
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"
 
 #undef	CONFIG_BOOTARGS
@@ -303,7 +298,7 @@
  */
 #define CFG_LONGHELP			/* undef to save memory	    */
 #define CFG_PROMPT		"=> "	/* Monitor Command Prompt   */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CFG_CBSIZE		256	/* Console I/O Buffer Size  */
@@ -319,6 +314,12 @@
 
 #define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
 
+#define CFG_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+
 /*
  * Various low-level settings
  */