X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FTQM8260.h;h=7fd12d3fbc6e355e5e65f85f802facba8c1acdca;hb=HEAD;hp=1b02cbbca7486b4083c990ac3e45afd90941ee56;hpb=326ea986ac150acdc7656d57fca647db80b50158;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h deleted file mode 100644 index 1b02cbb..0000000 --- a/include/configs/TQM8260.h +++ /dev/null @@ -1,624 +0,0 @@ -/* - * (C) Copyright 2001-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * Imported from global configuration: - * CONFIG_MPC8255 - * CONFIG_MPC8265 - * CONFIG_200MHz - * CONFIG_266MHz - * CONFIG_300MHz - * CONFIG_L2_CACHE - * CONFIG_BUSMODE_60x - */ - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_SYS_TEXT_BASE 0x40000000 - -#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */ - -#if 0 -#define CONFIG_TQM8260 100 /* ...on a TQM8260 module Rev.100 */ -#else -#define CONFIG_TQM8260 200 /* ...on a TQM8260 module Rev.200 */ -#endif - -#define CONFIG_CPM2 1 /* Has a CPM2 */ - -#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */ - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_BOOTCOUNT_LIMIT - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "bootfile=tqm8260/uImage\0" \ - "kernel_addr=400C0000\0" \ - "ramdisk_addr=40240000\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -/* enable I2C and select the hardware/software driver */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SOFT_SPEED 400000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F - -/* - * Software (bit-bang) I2C driver configuration - */ - -/* TQM8260 Rev.100 has the clock and data pins swapped (!!!) on EEPROM */ -#if (CONFIG_TQM8260 <= 100) - -#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ -#define I2C_ACTIVE (iop->pdir |= 0x00020000) -#define I2C_TRISTATE (iop->pdir &= ~0x00020000) -#define I2C_READ ((iop->pdat & 0x00020000) != 0) -#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00020000; \ - else iop->pdat &= ~0x00020000 -#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00010000; \ - else iop->pdat &= ~0x00010000 -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#else - -#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ -#define I2C_ACTIVE (iop->pdir |= 0x00010000) -#define I2C_TRISTATE (iop->pdir &= ~0x00010000) -#define I2C_READ ((iop->pdat & 0x00010000) != 0) -#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ - else iop->pdat &= ~0x00010000 -#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ - else iop->pdat &= ~0x00020000 -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -#define CONFIG_I2C_X - -/* - * select serial console configuration - * - * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - * - * if CONFIG_CONS_NONE is defined, then the serial console routines must - * defined elsewhere (for example, on the cogent platform, there are serial - * ports on the motherboard which are used for the serial console - see - * cogent/cma101/serial.[ch]). - */ -#define CONFIG_CONS_ON_SMC /* define if console on SMC */ -#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else*/ -#ifdef CONFIG_82xx_CONS_SMC1 -#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ -#endif -#ifdef CONFIG_82xx_CONS_SMC2 -#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ -#endif - -#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */ -#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */ -#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9 */ - -/* - * select ethernet configuration - * - * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then - * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 - * for FCC) - * - * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be - * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. - * - * (On TQM8260 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the - * X.29 connector, and FCC2 is hardwired to the X.1 connector) - */ -#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ -#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ -#undef CONFIG_ETHER_NONE /* define if ether on something else */ -#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ - -#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1) - -/* - * - RX clk is CLK11 - * - TX clk is CLK12 - */ -# define CONFIG_SYS_CMXSCR_VALUE1 (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12) - -#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) - -/* - * - Rx-CLK is CLK13 - * - Tx-CLK is CLK14 - * - RAM for BD/Buffers is on the 60x Bus (see 28-13) - * - Enable Full Duplex in FSMR - */ -# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) -# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) -# define CONFIG_SYS_CPMFCR_RAMTYPE 0 -# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) - -#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */ - - -/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ -#if defined(CONFIG_MPC8255) || defined(CONFIG_MPC8265) -# define CONFIG_8260_CLKIN 66666666 /* in Hz */ -#else /* !CONFIG_MPC8255 && !CONFIG_MPC8265 */ -# ifndef CONFIG_300MHz -# define CONFIG_8260_CLKIN 66666666 /* in Hz */ -# else -# define CONFIG_8260_CLKIN 83333000 /* in Hz */ -# endif -#endif /* CONFIG_MPC8255 */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_I2C -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_SYS_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - - -/* What should the base address of the main FLASH be and how big is - * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/tqm8260/config.mk - * The main FLASH is whichever is connected to *CS0. - */ -#define CONFIG_SYS_FLASH0_BASE 0x40000000 -#define CONFIG_SYS_FLASH1_BASE 0x60000000 -#define CONFIG_SYS_FLASH0_SIZE 32 -#define CONFIG_SYS_FLASH1_SIZE 32 - -/* Flash bank size (for preliminary settings) - */ -#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -/* use CFI flash driver */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CONFIG_SYS_FLASH_EMPTY_INFO 1 -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000) -#define CONFIG_ENV_SIZE 0x08000 -#define CONFIG_ENV_SECT_SIZE 0x40000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -/*----------------------------------------------------------------------- - * Hardware Information Block - */ -#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ -#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */ -#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ - -/*----------------------------------------------------------------------- - * Hard Reset Configuration Words - * - * if you change bits in the HRCW, you must also change the CONFIG_SYS_* - * defines for the various registers affected by the HRCW e.g. changing - * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR. - */ -#define __HRCW__ALL__ (HRCW_CIP | HRCW_ISB111 | HRCW_BMS) - -#if defined(CONFIG_MPC8255) || defined(CONFIG_MPC8265) -# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111) -#else /* ! MPC8255 && !MPC8265 */ -# if defined(CONFIG_266MHz) -# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111) -# elif defined(CONFIG_300MHz) -# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0110) -# else -# define CONFIG_SYS_HRCW_MASTER (__HRCW__ALL__) -# endif -#endif /* CONFIG_MPC8255 */ - -/* no slaves so just fill with zeros */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFFF00000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * - * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE, local SDRAM - * is mapped at SDRAM_BASE2_PRELIM. - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc()*/ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * HIDx - Hardware Implementation-dependent Registers 2-11 - *----------------------------------------------------------------------- - * HID0 also contains cache control - initially enable both caches and - * invalidate contents, then the final state leaves only the instruction - * cache enabled. Note that Power-On and Hard reset invalidate the caches, - * but Soft reset does not. - * - * HID1 has only read-only information - nothing to set. - */ -#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ - HID0_IFEM|HID0_ABE) -#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE) -#define CONFIG_SYS_HID2 0 - -/*----------------------------------------------------------------------- - * RMR - Reset Mode Register 5-5 - *----------------------------------------------------------------------- - * turn on Checkstop Reset Enable - */ -#define CONFIG_SYS_RMR RMR_CSRE - -/*----------------------------------------------------------------------- - * BCR - Bus Configuration 4-25 - *----------------------------------------------------------------------- - */ -#ifdef CONFIG_BUSMODE_60x -#define CONFIG_SYS_BCR (BCR_EBM|BCR_L2C|BCR_LETM|\ - BCR_NPQM0|BCR_NPQM1|BCR_NPQM2) /* 60x mode */ -#else -#define BCR_APD01 0x10000000 -#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */ -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 4-31 - *----------------------------------------------------------------------- - */ -#if 0 -#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10) -#else -#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10) -#endif - - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 4-35 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ - SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ - SYPCR_SWRI|SYPCR_SWP) -#endif /* CONFIG_WATCHDOG */ - -/*----------------------------------------------------------------------- - * TMCNTSC - Time Counter Status and Control 4-40 - *----------------------------------------------------------------------- - * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, - * and enable Time Counter - */ -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 4-42 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable - * Periodic timer - */ -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) - -/*----------------------------------------------------------------------- - * SCCR - System Clock Control 9-8 - *----------------------------------------------------------------------- - * Ensure DFBRG is Divide by 16 - */ -#define CONFIG_SYS_SCCR 0 - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration 13-7 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0 - -/* - * Init Memory Controller: - * - * Bank Bus Machine PortSz Device - * ---- --- ------- ------ ------ - * 0 60x GPCM 64 bit FLASH - * 1 60x SDRAM 64 bit SDRAM - * 2 Local SDRAM 32 bit SDRAM - * - */ - - /* Initialize SDRAM on local bus - */ -#define CONFIG_SYS_INIT_LOCAL_SDRAM - -#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ - -/* Minimum mask to separate preliminary - * address ranges for CS[0:2] - */ -#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */ -#define CONFIG_SYS_LOCAL_SDRAM_LIMIT (128<<20) /* less than 128 MB */ - -#define CONFIG_SYS_MPTPR 0x4000 - -/*----------------------------------------------------------------------------- - * Address for Mode Register Set (MRS) command - *----------------------------------------------------------------------------- - * In fact, the address is rather configuration data presented to the SDRAM on - * its address lines. Because the address lines may be mux'ed externally either - * for 8 column or 9 column devices, some bits appear twice in the 8260's - * address: - * - * | (RFU) | (RFU) | WBL | TM | CL | BT | Burst Length | - * | BA1 BA0 | A12 : A10 | A9 | A8 A7 | A6 : A4 | A3 | A2 : A0 | - * 8 columns mux'ing: | A9 | A10 A21 | A22 : A24 | A25 | A26 : A28 | - * 9 columns mux'ing: | A8 | A20 A21 | A22 : A24 | A25 | A26 : A28 | - * Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 | - *----------------------------------------------------------------------------- - */ -#define CONFIG_SYS_MRS_OFFS 0x00000110 - - -/* Bank 0 - FLASH - */ -#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_GPCM_P |\ - BRx_V) - -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ - ORxG_CSNT |\ - ORxG_ACS_DIV1 |\ - ORxG_SCY_3_CLK |\ - ORxG_EHTR |\ - ORxG_TRLX) - - /* SDRAM on TQM8260 can have either 8 or 9 columns. - * The number affects configuration values. - */ - -/* Bank 1 - 60x bus SDRAM - */ -#define CONFIG_SYS_PSRT 0x20 -#define CONFIG_SYS_LSRT 0x20 -#ifndef CONFIG_SYS_RAMBOOT -#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_SDRAM_P |\ - BRx_V) - -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1_8COL - - - /* SDRAM initialization values for 8-column chips - */ -#define CONFIG_SYS_OR1_8COL ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI1_A7 |\ - ORxS_NUMR_12) - -#define CONFIG_SYS_PSDMR_8COL (PSDMR_PBI |\ - PSDMR_SDAM_A15_IS_A5 |\ - PSDMR_BSMA_A12_A14 |\ - PSDMR_SDA10_PBI1_A8 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_2W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_2C |\ - PSDMR_EAMUX |\ - PSDMR_CL_2) - - /* SDRAM initialization values for 9-column chips - */ -#define CONFIG_SYS_OR1_9COL ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI1_A5 |\ - ORxS_NUMR_13) - -#define CONFIG_SYS_PSDMR_9COL (PSDMR_PBI |\ - PSDMR_SDAM_A16_IS_A5 |\ - PSDMR_BSMA_A12_A14 |\ - PSDMR_SDA10_PBI1_A7 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_2W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_2C |\ - PSDMR_EAMUX |\ - PSDMR_CL_2) - -/* Bank 2 - Local bus SDRAM - */ -#ifdef CONFIG_SYS_INIT_LOCAL_SDRAM -#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BRx_BA_MSK) |\ - BRx_PS_32 |\ - BRx_MS_SDRAM_L |\ - BRx_V) - -#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_8COL - -#define SDRAM_BASE2_PRELIM 0x80000000 - - /* SDRAM initialization values for 8-column chips - */ -#define CONFIG_SYS_OR2_8COL ((~(CONFIG_SYS_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI1_A8 |\ - ORxS_NUMR_12) - -#define CONFIG_SYS_LSDMR_8COL (PSDMR_PBI |\ - PSDMR_SDAM_A15_IS_A5 |\ - PSDMR_BSMA_A13_A15 |\ - PSDMR_SDA10_PBI1_A9 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_2W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_BL |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_2C |\ - PSDMR_CL_2) - - /* SDRAM initialization values for 9-column chips - */ -#define CONFIG_SYS_OR2_9COL ((~(CONFIG_SYS_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI1_A6 |\ - ORxS_NUMR_13) - -#define CONFIG_SYS_LSDMR_9COL (PSDMR_PBI |\ - PSDMR_SDAM_A16_IS_A5 |\ - PSDMR_BSMA_A13_A15 |\ - PSDMR_SDA10_PBI1_A8 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_2W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_BL |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_2C |\ - PSDMR_CL_2) - -#endif /* CONFIG_SYS_INIT_LOCAL_SDRAM */ - -#endif /* CONFIG_SYS_RAMBOOT */ - -#endif /* __CONFIG_H */