X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FT4240RDB.h;h=757fb054a8070862193cb6d511afbe33dfc13d09;hb=aca1f6789aa2e384a58909fa7a9696db9d607675;hp=1601ba9824ee77ae729b2df17eb9d4a0b7e1a15d;hpb=a0de075392fef8eb2d653a1fb54e7eb644b5353a;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/T4240RDB.h b/include/configs/T4240RDB.h
index 1601ba9..757fb05 100644
--- a/include/configs/T4240RDB.h
+++ b/include/configs/T4240RDB.h
@@ -12,7 +12,6 @@
 
 #include <linux/stringify.h>
 
-#define CONFIG_FSL_SATA_V2
 #define CONFIG_PCIE4
 
 #define CONFIG_ICS307_REFCLK_HZ		25000000  /* ICS307 ref clk freq */
@@ -22,9 +21,6 @@
 #define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
 #define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
 #else
-#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_PAD_TO		0x40000
-#define CONFIG_SPL_MAX_SIZE		0x28000
 #define RESET_VECTOR_OFFSET		0x27FFC
 #define BOOT_PAGE_OFFSET		0x27000
 
@@ -39,12 +35,6 @@
 #endif
 #endif
 
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_SKIP_RELOCATE
-#define CONFIG_SPL_COMMON_INIT_DDR
-#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
-#endif
-
 #endif
 #endif /* CONFIG_RAMBOOT_PBL */
 
@@ -60,13 +50,11 @@
 #define CONFIG_PCIE1			/* PCIE controller 1 */
 #define CONFIG_PCIE2			/* PCIE controller 2 */
 #define CONFIG_PCIE3			/* PCIE controller 3 */
-#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
 
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BTB			/* toggle branch predition */
 #ifdef CONFIG_DDR_ECC
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #endif
@@ -78,11 +66,7 @@
  */
 #define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
 #define CONFIG_SYS_L3_SIZE		(512 << 10)
-#define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 #define SPL_ENV_ADDR			(CONFIG_SPL_GD_ADDR + 4 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_ADDR	(CONFIG_SPL_GD_ADDR + 12 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_SIZE	(50 << 10)
-#define CONFIG_SPL_RELOC_STACK		(CONFIG_SPL_GD_ADDR + 64 * 1024)
 
 #define CONFIG_SYS_DCSRBAR		0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
@@ -94,21 +78,12 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	4
-
 /*
  * IFC Definitions
  */
 #define CONFIG_SYS_FLASH_BASE	0xe0000000
 #define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SPL_TEXT_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
-#endif
-
 #define CONFIG_HWCONFIG
 
 /* define to use L1 as initial stack */
@@ -123,9 +98,7 @@
 	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 #define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
 
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 #define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 
@@ -179,23 +152,6 @@
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 #endif	/* CONFIG_PCI */
 
-/* SATA */
-#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE	2
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
-#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
-#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
-
-#define CONFIG_LBA48
-#endif
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_ETHPRIME		"FM1@DTSEC1"
-#endif
-
 /*
  * Environment
  */
@@ -218,19 +174,12 @@
  * Environment Configuration
  */
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
-#define CONFIG_BOOTFILE		"uImage"
 #define CONFIG_UBOOTPATH	"u-boot.bin"	/* U-Boot image on TFTP server*/
 
 #define HVBOOT					\
 	"setenv bootargs config-addr=0x60000000; "	\
 	"bootm 0x01000000 - 0x00f00000"
 
-#define CONFIG_SYS_CLK_FREQ	66666666
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-#endif
-
 /*
  * DDR Setup
  */
@@ -274,7 +223,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
 
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
@@ -284,7 +232,6 @@ unsigned long get_board_sys_clk(void);
 					+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
 
 /* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
 #define CONFIG_SYS_NAND_MAX_ECCPOS	256
 #define CONFIG_SYS_NAND_MAX_OOBFREE	2
 #define CONFIG_SYS_NAND_BASE		0xff800000
@@ -305,8 +252,6 @@ unsigned long get_board_sys_clk(void);
 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
 				| CSOR_NAND_PB(128))	/*Page Per Block = 128*/
 
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
 /* ONFI NAND Flash mode0 Timing Params */
 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
 					FTIM0_NAND_TWP(0x18)   | \
@@ -411,12 +356,6 @@ unsigned long get_board_sys_clk(void);
 #define I2C_VOL_MONITOR_BUS_V_OVF	0x1
 #define I2C_VOL_MONITOR_BUS_V_SHIFT	3
 
-#define CONFIG_VID_FLS_ENV		"t4240rdb_vdd_mv"
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_VID
-#endif
-#define CONFIG_VOL_MONITOR_IR36021_SET
-#define CONFIG_VOL_MONITOR_IR36021_READ
 /* The lowest and highest voltage allowed for T4240RDB */
 #define VDD_MV_MIN			819
 #define VDD_MV_MAX			1212
@@ -459,24 +398,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_SYS_DPAA_RMAN
 #define CONFIG_SYS_INTERLAKEN
 
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 1MB (2048 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 0x820)
-#else
-#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 #endif /* CONFIG_NOBQFMAN */
 
@@ -499,29 +420,9 @@ unsigned long get_board_sys_clk(void);
 #define CORTINA_PHY_ADDR4	FM2_10GEC2_PHY_ADDR
 #endif
 
-/* SATA */
-#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE	2
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
-#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
-#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
-
-#define CONFIG_LBA48
-#endif
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_ETHPRIME		"FM1@DTSEC1"
-#endif
-
 /*
 * USB
 */
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_HAS_FSL_DR_USB
 
 #ifdef CONFIG_MMC
 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
@@ -568,40 +469,6 @@ unsigned long get_board_sys_clk(void);
 	"setenv bootargs config-addr=0x60000000; "	\
 	"bootm 0x01000000 - 0x00f00000"
 
-#define LINUXBOOTCOMMAND					\
-	"setenv bootargs root=/dev/ram rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"setenv ramdiskaddr 0x02000000;"		\
-	"setenv fdtaddr 0x00c00000;"			\
-	"setenv loadaddr 0x1000000;"			\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define HDBOOT					\
-	"setenv bootargs root=/dev/$bdev rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr - $fdtaddr"
-
-#define NFSBOOTCOMMAND			\
-	"setenv bootargs root=/dev/nfs rw "	\
-	"nfsroot=$serverip:$rootpath "		\
-	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"		\
-	"tftp $fdtaddr $fdtfile;"		\
-	"bootm $loadaddr - $fdtaddr"
-
-#define RAMBOOTCOMMAND				\
-	"setenv bootargs root=/dev/ram rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $ramdiskaddr $ramdiskfile;"		\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND		LINUXBOOTCOMMAND
-
 #include <asm/fsl_secure_boot.h>
 
 #endif	/* __CONFIG_H */