X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FT208xRDB.h;h=86dc5bfe82ad7bf6dcc0f508d64cc69b92c3b8b6;hb=0f9595b9fa68ed1634adddf989fd037909eec433;hp=886e0b745f3abbc5869f29f0934740821145ed33;hpb=c0ad62c5f7535bf13b24aab103356f827f40d0cd;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h
index 886e0b7..86dc5bf 100644
--- a/include/configs/T208xRDB.h
+++ b/include/configs/T208xRDB.h
@@ -39,7 +39,6 @@
 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
 #define CONFIG_SYS_NAND_U_BOOT_DST	0x00200000
 #define CONFIG_SYS_NAND_U_BOOT_START	0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)
 #endif
 
 #ifdef CONFIG_SPIFLASH
@@ -89,12 +88,6 @@
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #endif
 
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ	66660000
-
 /*
  * Config the L3 Cache as L3 SRAM
  */
@@ -158,7 +151,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
 
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
@@ -188,7 +180,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_SYS_CS2_FTIM3		0x0
 
 /* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
 #define CONFIG_SYS_NAND_BASE		0xff800000
 #define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
 
@@ -313,12 +304,6 @@ unsigned long get_board_sys_clk(void);
 
 #define I2C_MUX_CH_VOL_MONITOR	0xa
 
-#define CONFIG_VID_FLS_ENV		"t208xrdb_vdd_mv"
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_VID
-#endif
-#define CONFIG_VOL_MONITOR_IR36021_SET
-#define CONFIG_VOL_MONITOR_IR36021_READ
 /* The lowest and highest voltage allowed for T208xRDB */
 #define VDD_MV_MIN			819
 #define VDD_MV_MAX			1212
@@ -373,7 +358,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_PCIE2		/* PCIE controller 2 */
 #define CONFIG_PCIE3		/* PCIE controller 3 */
 #define CONFIG_PCIE4		/* PCIE controller 4 */
-#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 #define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
@@ -435,35 +419,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_SYS_DPAA_RMAN		/* RMan */
 #define CONFIG_SYS_INTERLAKEN
 
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR		0x110000
-
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 1MB (2048 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x820)
-
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-/*
- * Slave has no ucode locally, it can fetch this from remote. When implementing
- * in two corenet boards, slave's ucode could be stored in master's memory
- * space, the address can be mapped from slave TLB->slave LAW->
- * slave SRIO or PCIE outbound window->master inbound window->
- * master LAW->the ucode address in master's memory space.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR		0xFFE00000
-#else
-#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 #endif /* CONFIG_NOBQFMAN */
 
@@ -502,7 +457,6 @@ unsigned long get_board_sys_clk(void);
  * USB
  */
 #ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_HAS_FSL_DR_USB
 #endif
@@ -597,40 +551,6 @@ unsigned long get_board_sys_clk(void);
 	"cpu 7 release 0x01000000 - - -;"		\
 	"go 0x01000000"
 
-#define LINUXBOOTCOMMAND				\
-	"setenv bootargs root=/dev/ram rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"setenv ramdiskaddr 0x02000000;"		\
-	"setenv fdtaddr 0x00c00000;"			\
-	"setenv loadaddr 0x1000000;"			\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define HDBOOT					\
-	"setenv bootargs root=/dev/$bdev rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr - $fdtaddr"
-
-#define NFSBOOTCOMMAND			\
-	"setenv bootargs root=/dev/nfs rw "	\
-	"nfsroot=$serverip:$rootpath "		\
-	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"		\
-	"tftp $fdtaddr $fdtfile;"		\
-	"bootm $loadaddr - $fdtaddr"
-
-#define RAMBOOTCOMMAND				\
-	"setenv bootargs root=/dev/ram rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $ramdiskaddr $ramdiskfile;"		\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND		LINUXBOOTCOMMAND
-
 #include <asm/fsl_secure_boot.h>
 
 #endif	/* __T2080RDB_H */