X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FT1040QDS.h;h=e890860b7e58e3f5239c1b214d5af564e428dc91;hb=8ccf98b1cfd2811e3121c719e294bdd8ebab1c45;hp=bf2c15a18329d1ba09daa324fbe744b31b506f85;hpb=0ddc9c172279f686077310fbcfa5baf10c719188;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h
index bf2c15a..e890860 100644
--- a/include/configs/T1040QDS.h
+++ b/include/configs/T1040QDS.h
@@ -36,15 +36,10 @@
 
 /* High Level Configuration Options */
 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
-#define CONFIG_MP			/* support multiple processors */
 
 /* support deep sleep */
 #define CONFIG_DEEP_SLEEP
 
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xeff40000
-#endif
-
 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
 #endif
@@ -126,8 +121,6 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_PANIC_HANG	/* do not reset board on panic */
 
 /*
  *  Config the L3 Cache as L3 SRAM
@@ -283,7 +276,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_NAND_DDR_LAW		11
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_CMD_NAND
 
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
 
@@ -345,9 +337,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_RAMBOOT
 #endif
 
-#define CONFIG_BOARD_EARLY_INIT_R
-#define CONFIG_MISC_INIT_R
-
 #define CONFIG_HWCONFIG
 
 /* define to use L1 as initial stack */
@@ -373,7 +362,6 @@ unsigned long get_board_ddr_clk(void);
  * open - index 2
  * shorted - index 1
  */
-#define CONFIG_CONS_INDEX	1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
@@ -501,9 +489,6 @@ unsigned long get_board_ddr_clk(void);
 /* SATA */
 #define CONFIG_FSL_SATA_V2
 #ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_LIBATA
-#define CONFIG_FSL_SATA
-
 #define CONFIG_SYS_SATA_MAX_DEVICE	2
 #define CONFIG_SATA1
 #define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
@@ -528,7 +513,6 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 #ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
 #define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #define CONFIG_FSL_ESDHC_ADAPTER_IDENT
@@ -536,7 +520,6 @@ unsigned long get_board_ddr_clk(void);
 
 /* Qman/Bman */
 #ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
 #define CONFIG_SYS_BMAN_NUM_PORTALS	10
 #define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
 #define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
@@ -616,9 +599,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f
 
-#define CONFIG_MII		/* MII PHY management */
 #define CONFIG_ETHPRIME		"FM1@DTSEC1"
-#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
 #endif
 
 /* Enable VSC9953 L2 Switch driver */
@@ -630,16 +611,7 @@ unsigned long get_board_ddr_clk(void);
  * Dynamic MTD Partition support with mtdparts
  */
 #ifdef CONFIG_MTD_NOR_FLASH
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
 #define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
-			"spi0=spife110000.0"
-#define MTDPARTS_DEFAULT	"mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
-				"128k(dtb),96m(fs),-(user);"\
-				"fff800000.flash:2m(uboot),9m(kernel),"\
-				"128k(dtb),96m(fs),-(user);spife110000.0:" \
-				"2m(uboot),9m(kernel),128k(dtb),-(user)"
 #endif
 
 /*
@@ -649,29 +621,9 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
 
 /*
- * Command line configuration.
- */
-#define CONFIG_CMD_REGINFO
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#endif
-
-/*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
-#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
-#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 
 /*
  * For booting Linux, the board info and command line data