X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FSMN42.h;h=d6f41f926d3bc5cfdc811a11b64f7d48a4ca37f8;hb=488f5d8790c451fc527fe5d2ef218f2a5e40ea17;hp=d588818fc2ebb3b1c30bd7911ec8a32d95890ef9;hpb=725671ccd2cd04c9ebc50c9e5a94dd8cbade66b7;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/SMN42.h b/include/configs/SMN42.h old mode 100755 new mode 100644 index d588818..d6f41f9 --- a/include/configs/SMN42.h +++ b/include/configs/SMN42.h @@ -49,8 +49,8 @@ /* * Size of malloc() pool */ -#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ /* * Hardware drivers @@ -66,19 +66,27 @@ #define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE) +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE + /* enable I2C and select the hardware/software driver */ #undef CONFIG_HARD_I2C /* I2C with hardware support */ #define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ /* this would be 0xAE if E0, E1 and E2 were pulled high */ -#define CFG_I2C_SLAVE 0xA0 -#define CFG_I2C_EEPROM_ADDR (0xA0 >> 1) -#define CFG_I2C_EEPROM_ADDR_LEN 2 /* 16 bit address */ -#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes per write */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 +#define CONFIG_SYS_I2C_SLAVE 0xA0 +#define CONFIG_SYS_I2C_EEPROM_ADDR (0xA0 >> 1) +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16 bit address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes per write */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 /* not used but required by devices.c */ -#define CFG_I2C_SPEED 10000 +#define CONFIG_SYS_I2C_SPEED 10000 #ifdef CONFIG_SOFT_I2C /* @@ -101,47 +109,44 @@ PUT32(IO0DIR, i2ctmp); } #endif /* CONFIG_SOFT_I2C */ + /* - * Supported commands + * Command line configuration. */ -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_DHCP | \ - CFG_CMD_FAT | \ - CFG_CMD_MMC | \ - CFG_CMD_NET | \ - CFG_CMD_EEPROM | \ - CFG_CMD_PING) +#include +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_FAT +#define CONFIG_CMD_MMC +#define CONFIG_CMD_NET +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_PING -#define CONFIG_DOS_PARTITION -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include +#define CONFIG_DOS_PARTITION #define CONFIG_BOOTDELAY 5 /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "SMN42 # " /* Monitor Command Prompt */ -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x81800000 /* memtest works on */ -#define CFG_MEMTEST_END 0x83000000 /* 24 MB in SRAM */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "SMN42 # " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ +#define CONFIG_SYS_MEMTEST_START 0x81800000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x83000000 /* 24 MB in SRAM */ -#define CFG_LOAD_ADDR 0x81000000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x81000000 /* default load address */ /* for uClinux img is here*/ -#define CFG_SYS_CLK_FREQ 58982400 /* Hz */ -#define CFG_HZ 2048 /* decrementer freq in Hz */ +#define CONFIG_SYS_SYS_CLK_FREQ 58982400 /* Hz */ +#define CONFIG_SYS_HZ 2048 /* decrementer freq in Hz */ /* valid baudrates */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /*----------------------------------------------------------------------- * Stack sizes @@ -170,24 +175,24 @@ */ /* - * The first entry in CFG_FLASH_BANKS_LIST is a dummy, but it must be present. + * The first entry in CONFIG_SYS_FLASH_BANKS_LIST is a dummy, but it must be present. */ -#define CFG_FLASH_BANKS_LIST { 0, PHYS_FLASH_1 } -#define CFG_FLASH_ADDR0 0x555 -#define CFG_FLASH_ADDR1 0x2AA -#define CFG_FLASH_ERASE_TOUT 16384 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_BANKS_LIST { 0, PHYS_FLASH_1 } +#define CONFIG_SYS_FLASH_ADDR0 0x555 +#define CONFIG_SYS_FLASH_ADDR1 0x2AA +#define CONFIG_SYS_FLASH_ERASE_TOUT 16384 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */ -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ -#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CFG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_IS_IN_FLASH 1 /* The Environment Sector is in the CPU-internal flash */ -#define CFG_FLASH_BASE 0 -#define CFG_ENV_OFFSET 0x3C000 -#define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_ENV_OFFSET) -#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CONFIG_SYS_FLASH_BASE 0 +#define CONFIG_ENV_OFFSET 0x3C000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ #define CONFIG_CMDLINE_TAG #define CONFIG_SETUP_MEMORY_TAGS