X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FPMC405.h;h=966bbf9a3188ea6710114bfd5d2dfd86faf3218f;hb=ce0eb70333331da6942167c41e6841c8c7994a33;hp=54b53bc71f1dbd4556845f33a168c0dc56ea3eb3;hpb=8bde7f776c77b343aca29b8c7b58464d915ac245;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/PMC405.h b/include/configs/PMC405.h index 54b53bc..966bbf9 100644 --- a/include/configs/PMC405.h +++ b/include/configs/PMC405.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2001-2003 + * (C) Copyright 2001-2004 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com * * See file CREDITS for list of people who contributed to this @@ -34,57 +34,72 @@ */ #define CONFIG_405GP 1 /* This is a PPC405 CPU */ -#define CONFIG_4xx 1 /* ...member of PPC4xx family */ -#define CONFIG_PMC405 1 /* ...on a PMC405 board */ +#define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_PMC405 1 /* ...on a PMC405 board */ -#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */ -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ +#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */ #define CONFIG_BAUDRATE 9600 #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ #undef CONFIG_BOOTARGS -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ - "bootm ffc00000 ffca0000" -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ - "bootm ffc00000" -#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND +#undef CONFIG_BOOTCOMMAND + +#define CONFIG_PREBOOT /* enable preboot variable */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 + #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ - -#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ - CFG_CMD_PCI | \ - CFG_CMD_IRQ | \ - CFG_CMD_ELF | \ - CFG_CMD_DATE | \ - CFG_CMD_JFFS2 | \ - CFG_CMD_MII | \ - CFG_CMD_I2C | \ - CFG_CMD_PING | \ - CFG_CMD_EEPROM ) +#define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ + +#define CONFIG_NETCONSOLE /* include NetConsole support */ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_BSP +#define CONFIG_CMD_PCI +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_ELF +#define CONFIG_CMD_DATE +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_I2C +#define CONFIG_CMD_PING +#define CONFIG_CMD_UNIVERSE +#define CONFIG_CMD_EEPROM + #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include - -#undef CONFIG_WATCHDOG /* watchdog disabled */ +#undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ -#define CFG_RTC_REG_BASE_ADDR 0xF0000300 /* RTC Base Address */ +#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ -#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ /* * Miscellaneous configurable options @@ -94,44 +109,48 @@ #undef CFG_HUSH_PARSER /* use "hush" command parser */ #ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CFG_PROMPT_HUSH_PS2 "> " #endif -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */ +#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */ + +#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */ -#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */ -#define CFG_BASE_BAUD 691200 +#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */ +#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */ +#define CFG_BASE_BAUD 691200 /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ +#define CFG_BAUDRATE_TABLE \ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ 57600, 115200, 230400, 460800, 921600 } #define CFG_LOAD_ADDR 0x100000 /* default load address */ #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_LOOPW 1 /* enable loopw command */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ +#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ /*----------------------------------------------------------------------- * PCI stuff @@ -142,22 +161,35 @@ #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ /* resource configuration */ -#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ +#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ + +#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/ + +#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ #define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0408 /* PCI Device ID: PMC-405 */ +#define CFG_PCI_SUBSYS_DEVICEID_NONMONARCH 0x0408 /* PCI Device ID: Non-Monarch */ +#define CFG_PCI_SUBSYS_DEVICEID_MONARCH 0x0409 /* PCI Device ID: Monarch */ +#define CFG_PCI_SUBSYS_DEVICEID pmc405_pci_subsys_deviceid() + #define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ + +#define CFG_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */ +#define CFG_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */ #define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#if 1 +#define CFG_PCI_PTM2LA 0xef000000 /* point to internal regs */ +#define CFG_PCI_PTM2MS 0xff000001 /* 16MB, enable */ +#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ +#else /* old mapping */ #define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */ #define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ #define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - +#endif /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) @@ -178,29 +210,47 @@ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ -#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#undef CFG_FLASH_PROTECTION /* don't use hardware protection */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CFG_FLASH_BASE 0xFE000000 #define CFG_FLASH_INCREMENT 0x01000000 -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_FLASH_PROTECTION 1 /* don't use hardware protection */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_MAX_FLASH_BANKS 2 /* max num of flash banks */ +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE + CFG_FLASH_INCREMENT } +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ -#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ -#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains u-boot */ +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +/* + * JFFS2 partitions - second bank contains u-boot + * + */ +/* No command line, one static partition, whole device */ +#undef CONFIG_JFFS2_CMDLINE +#define CONFIG_JFFS2_DEV "nor0" +#define CONFIG_JFFS2_PART_SIZE 0x01b00000 +#define CONFIG_JFFS2_PART_OFFSET 0x00400000 + +/* mtdparts command line support */ +/* Note: fake mtd_id used, no linux mtd map file */ +/* +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nor0=pmc405-0" +#define MTDPARTS_DEFAULT "mtdparts=pmc405-0:-(jffs2)" +*/ /*----------------------------------------------------------------------- * Environment Variable setup */ -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ -#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ +#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ /* total size of a CAT24WC16 is 2048 bytes */ #define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ -#define CFG_NVRAM_SIZE 242 /* NVRAM size */ +#define CFG_NVRAM_SIZE 242 /* NVRAM size */ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment @@ -210,56 +260,72 @@ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ #define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 #define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ /* 16 byte page write mode using*/ - /* last 4 bits of the address */ + /* last 4 bits of the address */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE /*----------------------------------------------------------------------- - * Cache Configuration + * External Bus Controller (EBC) Setup */ -#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif +#define FLASH0_BA 0xFF000000 /* FLASH 0 Base Address */ +#define FLASH1_BA 0xFE000000 /* FLASH 1 Base Address */ +#define CAN_BA 0xF0000000 /* CAN Base Address */ +#define RTC_BA 0xF0000500 /* RTC Base Address */ +#define NVRAM_BA 0xF0200000 /* NVRAM Base Address */ + +/* Memory Bank 0 (Flash Bank 0) initialization */ +#define CFG_EBC_PB0AP 0x92015480 +#define CFG_EBC_PB0CR FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/ + +/* Memory Bank 1 (Flash Bank 1) initialization */ +#define CFG_EBC_PB1AP 0x92015480 +#define CFG_EBC_PB1CR FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/ + +/* Memory Bank 2 (CAN0, 1, RTC) initialization */ +#define CFG_EBC_PB2AP 0x03000440 /* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0 */ +#define CFG_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 3 -> unused */ + +/* Memory Bank 4 (NVRAM) initialization */ +#define CFG_EBC_PB4AP 0x03000440 /* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0 */ +#define CFG_EBC_PB4CR NVRAM_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ /*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup + * FPGA stuff */ -#define FLASH0_BA 0xFF000000 /* FLASH 0 Base Address */ -#define FLASH1_BA 0xFE000000 /* FLASH 1 Base Address */ -#define CAN_BA 0xF0000000 /* CAN Base Address */ -#define RTC_BA 0xF0000500 /* RTC Base Address */ -#define CF_BA 0xF0100000 /* CompactFlash Base Address */ - -/* Memory Bank 0 (Flash Bank 0) initialization */ -#define CFG_EBC_PB0AP 0x92015480 -#define CFG_EBC_PB0CR FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/ +#define CFG_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */ +#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */ -/* Memory Bank 1 (Flash Bank 1) initialization */ -#define CFG_EBC_PB1AP 0x92015480 -#define CFG_EBC_PB1CR FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/ +/* FPGA program pin configuration */ +#define CFG_FPGA_PRG 0x04000000 /* JTAG TMS pin (ppc output) */ +#define CFG_FPGA_CLK 0x02000000 /* JTAG TCK pin (ppc output) */ +#define CFG_FPGA_DATA 0x01000000 /* JTAG TDO->TDI data pin (ppc output) */ +#define CFG_FPGA_INIT 0x00010000 /* unused (ppc input) */ +#define CFG_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */ -/* Memory Bank 2 (CAN0, 1, RTC) initialization */ -#define CFG_EBC_PB2AP 0x03000040 /* TWT=6,TH=0,CSN=0,OEN=0,WBN=0,WBF=0 */ -#define CFG_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ +#define CFG_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */ -/* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization */ -#define CFG_EBC_PB3AP 0x010059C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ -#define CFG_EBC_PB3CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ +/*----------------------------------------------------------------------- + * GPIOs + */ +#define CFG_NONMONARCH (0x80000000 >> 14) /* GPIO24 */ +#define CFG_XEREADY (0x80000000 >> 15) /* GPIO15 */ +#define CFG_INTA_FAKE (0x80000000 >> 19) /* GPIO19 */ +#define CFG_SELF_RST (0x80000000 >> 21) /* GPIO21 */ +#define CFG_REV1_2 (0x80000000 >> 23) /* GPIO23 */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in data cache) */ /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CFG_TEMP_STACK_OCM 1 +#define CFG_TEMP_STACK_OCM 1 /* On Chip Memory location */ #define CFG_OCM_DATA_ADDR 0xF8000000 @@ -269,7 +335,7 @@ #define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET /* * Internal Definitions