X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FPM828.h;h=96c0edf93971284a1432b015a672c9d2820b7443;hb=d3c23a790fb24f9cb5cc467b81b0c3ad3eeb1f96;hp=7d98df5cac4435b884b710fdcc700399118e5935;hpb=d56019c0eed08632c2b1f828ca9e0b22d6151414;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/PM828.h b/include/configs/PM828.h
index 7d98df5..96c0edf 100644
--- a/include/configs/PM828.h
+++ b/include/configs/PM828.h
@@ -43,13 +43,13 @@
 
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 
-#define CONFIG_PREBOOT	"echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
 
 #undef	CONFIG_BOOTARGS
 #define CONFIG_BOOTCOMMAND							\
 	"bootp;"								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
-	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
+	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"	\
 	"bootm"
 
 /* enable I2C and select the hardware/software driver */
@@ -103,8 +103,7 @@
  *   - CONFIG_NET_MULTI must be defined
  *
  * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
- * from CONFIG_COMMANDS to remove support for networking.
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
  */
 #define CONFIG_NET_MULTI
 #undef	CONFIG_ETHER_NONE		/* define if ether on something else */
@@ -152,37 +151,39 @@
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DOC
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
 
 #ifdef CONFIG_PCI
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_BEDBUG	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_DOC	| \
-				CFG_CMD_EEPROM	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_SNTP	)
-#else	/* ! PCI */
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_BEDBUG	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_DOC	| \
-				CFG_CMD_EEPROM	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_SNTP	)
-#endif	/* CONFIG_PCI */
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_CMD_PCI
+#endif
+
 
 /*
  * Disk-On-Chip configuration
  */
+#define CONFIG_NAND_LEGACY
 
 #define CFG_DOC_SHORT_TIMEOUT
 #define CFG_MAX_DOC_DEVICE	1	/* Max number of DOC devices	*/
@@ -195,7 +196,7 @@
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -337,7 +338,7 @@
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE	32	/* For MPC8260 CPU		*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif