X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FPM828.h;h=49b4571e1ac139d5cb0360f2a30afffc72ca54d7;hb=5a89fa927cf6c54efe36918a4894ce31274d9ef1;hp=96c86f7e90130f9657bc08543e2a0088bf594c32;hpb=f61f1e150c84f5b9347fca79a4bc5f2286c545d2;p=kernel%2Fu-boot.git

diff --git a/include/configs/PM828.h b/include/configs/PM828.h
index 96c86f7..49b4571 100644
--- a/include/configs/PM828.h
+++ b/include/configs/PM828.h
@@ -2,23 +2,7 @@
  * (C) Copyright 2001-2005
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier:	GPL-2.0+
  */
 
 /*
@@ -39,6 +23,10 @@
 #define CONFIG_PM828		1	/* ...on a PM828 module */
 #define CONFIG_CPM2		1	/* Has a CPM2 */
 
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0x40000000	/* Standard: boot 64-bit flash */
+#endif
+
 #undef CONFIG_DB_CR826_J30x_ON		/* J30x jumpers on D.B. carrier */
 
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
@@ -53,10 +41,10 @@
 	"bootm"
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-# define CONFIG_SYS_I2C_SPEED		50000
-# define CONFIG_SYS_I2C_SLAVE		0xFE
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -96,16 +84,13 @@
  *
  * if CONFIG_ETHER_ON_SCC is selected, then
  *   - CONFIG_ETHER_INDEX must be set to the channel number (1-4)
- *   - CONFIG_NET_MULTI must not be defined
  *
  * if CONFIG_ETHER_ON_FCC is selected, then
  *   - one or more CONFIG_ETHER_ON_FCCx (x=1,2,3) must also be selected
- *   - CONFIG_NET_MULTI must be defined
  *
  * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
  * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
  */
-#define CONFIG_NET_MULTI
 #undef	CONFIG_ETHER_NONE		/* define if ether on something else */
 
 #undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC	*/
@@ -169,33 +154,20 @@
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP
 
 #ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_CMD_PCI
 #endif
 
-
-/*
- * Disk-On-Chip configuration
- */
-#define CONFIG_NAND_LEGACY
-
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_MAX_DOC_DEVICE	1	/* Max number of DOC devices	*/
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
@@ -210,10 +182,6 @@
 
 #define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
 
-#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
 #define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC	/* "bad" address		*/
 
 /*
@@ -296,9 +264,8 @@
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_END	0x4000	/* End of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_SIZE	128 /* size in bytes reserved for initial data*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE	0x4000	/* Size of used area in DPRAM	*/
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -311,7 +278,7 @@
  */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
 #define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()*/
 
@@ -325,15 +292,6 @@
 #define CONFIG_SYS_RX_ETH_BUFFER	8		/* use 8 rx buffer on eepro100	*/
 #endif
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH*/
-#define BOOTFLAG_WARM		0x02	/* Software reboot		   */
-
-
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */