X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FPM828.h;h=28666d646b32e8c8e5fa8d60855b0b4413ee65d5;hb=544aa66a6695790227613bf32bdf672143d5a1ad;hp=96c86f7e90130f9657bc08543e2a0088bf594c32;hpb=50bd0057ba8fceeb48533f8b1a652ccd0e170838;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/PM828.h b/include/configs/PM828.h
index 96c86f7..28666d6 100644
--- a/include/configs/PM828.h
+++ b/include/configs/PM828.h
@@ -39,6 +39,10 @@
 #define CONFIG_PM828		1	/* ...on a PM828 module */
 #define CONFIG_CPM2		1	/* Has a CPM2 */
 
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0x40000000	/* Standard: boot 64-bit flash */
+#endif
+
 #undef CONFIG_DB_CR826_J30x_ON		/* J30x jumpers on D.B. carrier */
 
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
@@ -105,7 +109,6 @@
  * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
  * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
  */
-#define CONFIG_NET_MULTI
 #undef	CONFIG_ETHER_NONE		/* define if ether on something else */
 
 #undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC	*/
@@ -169,7 +172,6 @@
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_NFS
@@ -179,18 +181,6 @@
 #define CONFIG_CMD_PCI
 #endif
 
-
-/*
- * Disk-On-Chip configuration
- */
-#define CONFIG_NAND_LEGACY
-
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_MAX_DOC_DEVICE	1	/* Max number of DOC devices	*/
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
 /*
  * Miscellaneous configurable options
  */
@@ -296,9 +286,8 @@
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_END	0x4000	/* End of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_SIZE	128 /* size in bytes reserved for initial data*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE	0x4000	/* Size of used area in DPRAM	*/
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -311,7 +300,7 @@
  */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
 #define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()*/
 
@@ -325,15 +314,6 @@
 #define CONFIG_SYS_RX_ETH_BUFFER	8		/* use 8 rx buffer on eepro100	*/
 #endif
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH*/
-#define BOOTFLAG_WARM		0x02	/* Software reboot		   */
-
-
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */