X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FP1010RDB.h;h=384027c21d183558edcecbfbaeffd394aac5a0bc;hb=fa379223cd61052331342e525778d96270ee6ed9;hp=867004fb4899853affd3119e7ab6d7df2f0db7ed;hpb=64d6ac5bc4a9bf8839e516959b35150ac8a0eb84;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index 867004f..384027c 100644
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -140,8 +140,6 @@
 #define CONFIG_FSL_PCIE_RESET		/* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
 
-#define CONFIG_CMD_PCI
-
 /*
  * PCI Windows
  * Memory space is mapped 1-1, but I/O space must start from 0.
@@ -354,7 +352,6 @@ extern unsigned long get_sdram_size(void);
 
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITION
-#define CONFIG_CMD_MTDPARTS
 #define MTDIDS_DEFAULT			"nand0=ff800000.flash"
 #define MTDPARTS_DEFAULT		\
 	"mtdparts=ff800000.flash:2m(uboot-env),1m(dtb),5m(kernel),56m(fs),-(usr)"
@@ -389,7 +386,6 @@ extern unsigned long get_sdram_size(void);
 
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_CMD_NAND
 
 #if defined(CONFIG_TARGET_P1010RDB_PA)
 /* NAND Flash Timing Params */
@@ -589,7 +585,6 @@ extern unsigned long get_sdram_size(void);
 #define MAX_NUM_PORTS			9 /* for 128Bytes EEPROM */
 #endif
 /* enable read and write access to EEPROM */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -632,8 +627,6 @@ extern unsigned long get_sdram_size(void);
 
 #define CONFIG_ETHPRIME		"eTSEC1"
 
-#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
-
 /* TBI PHY configuration for SGMII mode */
 #define CONFIG_TSEC_TBICR_SETTINGS ( \
 		TBICR_PHY_RESET \
@@ -658,7 +651,6 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
 #define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
 
-#define CONFIG_CMD_SATA
 #define CONFIG_LBA48
 #endif /* #ifdef CONFIG_FSL_SATA  */
 
@@ -680,12 +672,10 @@ extern unsigned long get_sdram_size(void);
  * Environment
  */
 #if defined(CONFIG_SDCARD)
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_FSL_FIXED_MMC_LOCATION
 #define CONFIG_SYS_MMC_ENV_DEV		0
 #define CONFIG_ENV_SIZE			0x2000
 #elif defined(CONFIG_SPIFLASH)
-#define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SPI_BUS	0
 #define CONFIG_ENV_SPI_CS	0
 #define CONFIG_ENV_SPI_MAX_HZ	10000000
@@ -694,7 +684,6 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_ENV_SECT_SIZE	0x10000
 #define CONFIG_ENV_SIZE		0x2000
 #elif defined(CONFIG_NAND)
-#define CONFIG_ENV_IS_IN_NAND
 #ifdef CONFIG_TPL_BUILD
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
@@ -709,11 +698,9 @@ extern unsigned long get_sdram_size(void);
 #endif
 #define CONFIG_ENV_OFFSET	(1024 * 1024)
 #elif defined(CONFIG_SYS_RAMBOOT)
-#define CONFIG_ENV_IS_NOWHERE		/* Store ENV in memory only */
 #define CONFIG_ENV_ADDR			(CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE			0x2000
 #else
-#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR	(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
@@ -722,25 +709,12 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_LOADS_ECHO		/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
 
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI_HCD) \
 		 || defined(CONFIG_FSL_SATA)
 #endif
 
-/* Hash command with SHA acceleration supported in hardware */
-#ifdef CONFIG_FSL_CAAM
-#define CONFIG_CMD_HASH
-#define CONFIG_SHA_HW_ACCEL
-#endif
-
 /*
  * Miscellaneous configurable options
  */