X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FNSCU.h;h=f13cb345c3955fbc14c808d83c873f63bb089947;hb=cfca5e604d5692f081cc1a9185ca5dc6dc77599d;hp=930a5be75a4dc9bd0d92f9381d55236aeca7551f;hpb=45eeb8983c3eca0e82178897c027a34a52295a0f;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/NSCU.h b/include/configs/NSCU.h
index 930a5be..f13cb34 100644
--- a/include/configs/NSCU.h
+++ b/include/configs/NSCU.h
@@ -45,8 +45,6 @@
 
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 
-#undef	CONFIG_CLOCKS_IN_MHZ		/* clocks passsed to Linux in Hz */
-
 #define CONFIG_BOARD_TYPES	1	/* support board types		*/
 
 #define CONFIG_PREBOOT	"echo;"	\
@@ -75,6 +73,8 @@
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
+#define CONFIG_MISC_INIT_R	  1
+
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
 
@@ -252,15 +252,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
  */
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -269,17 +262,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -355,19 +340,8 @@
 /*
  * FLASH timing:
  */
-#if   defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -437,13 +411,9 @@
  * 66 Mhz => 66.000.000 / Divider = 129
  * 80 Mhz => 80.000.000 / Divider = 156
  */
-#if   defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us