X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8641HPCN.h;h=9b2623c72620a54ec23b585286f5fc4b477a6bd9;hb=4b6e1fda107e5244e80ebc41865650ac2873dc88;hp=6f1535ec1ec3812a9b7c22159219a05123239bff;hpb=e573bdb324c78fac56655a493bea843842c9d9f8;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 6f1535e..9b2623c 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -46,8 +46,8 @@
 #define CONFIG_SRIO1			/* SRIO port 1 */
 
 #define CONFIG_PCI		1	/* Enable PCI/PCIE */
-#define CONFIG_PCIE1		1	/* PCIE controler 1 (ULI bridge) */
-#define CONFIG_PCIE2		1	/* PCIE controler 2 (slot) */
+#define CONFIG_PCIE1		1	/* PCIE controller 1 (ULI bridge) */
+#define CONFIG_PCIE2		1	/* PCIE controller 2 (slot) */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
 #define CONFIG_FSL_LAW		1	/* Use common FSL law init code */
@@ -134,7 +134,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define SPD_EEPROM_ADDRESS3	0x53	/* CTLR 1 DIMM 0 */
 #define SPD_EEPROM_ADDRESS4	0x54	/* CTLR 1 DIMM 1 */
 
-
 /*
  * These are used when DDR doesn't use SPD.
  */
@@ -259,7 +258,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX     1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
@@ -270,16 +268,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree to kernel
- */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
 /*
  * I2C
  */
@@ -366,12 +354,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 
-#undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE
-
 #define CONFIG_PCI_PNP			/* do pci plug-and-play */
 
-#define CONFIG_RTL8139
-
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -403,7 +387,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_VGA_AS_SINGLE_DEVICE
 #define CONFIG_ATI_RADEON_FB
 #define CONFIG_VIDEO_LOGO
-/*#define CONFIG_CONSOLE_CURSOR*/
 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT
 #endif
 
@@ -453,7 +436,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #endif	/* CONFIG_TSEC_ENET */
 
-
 #ifdef CONFIG_PHYS_64BIT
 #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8)
 #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2)
@@ -613,7 +595,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
-
 /*
  * BOOTP options
  */
@@ -622,22 +603,16 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
-    #define CONFIG_CMD_SCSI
-    #define CONFIG_CMD_EXT2
-    #define CONFIG_CMD_USB
+    #define CONFIG_SCSI
 #endif
 
-
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
 /*
@@ -719,7 +694,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 	"dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \
 	"maxcpus=2"
 
-
 #define CONFIG_NFSBOOTCOMMAND						\
 	"setenv bootargs root=/dev/nfs rw "				\
 	      "nfsroot=$serverip:$rootpath "				\