X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8610HPCD.h;h=4ce04a84aa5092970c7631a626525543c2e84527;hb=09f3ca3dd53b671b009ddc4e1dad669c280094f0;hp=9128c985fb1c2a6f5b0a27f801b6e32b0ee1586a;hpb=2ae1824196884ba2bafffb7c0d3e8297350591e9;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index 9128c98..4ce04a8 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2007 Freescale Semiconductor, Inc.
+ * Copyright 2007-2011 Freescale Semiconductor, Inc.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -13,22 +13,25 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#define CONFIG_DISPLAY_BOARDINFO
+
 /* High Level Configuration Options */
-#define CONFIG_MPC86xx		1	/* MPC86xx */
 #define CONFIG_MPC8610		1	/* MPC8610 specific */
 #define CONFIG_MPC8610HPCD	1	/* MPC8610HPCD board specific */
 #define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
 
 #define	CONFIG_SYS_TEXT_BASE	0xfff00000
 
-#define CONFIG_FSL_DIU_FB	1	/* FSL DIU */
 
 /* video */
-#undef CONFIG_VIDEO
+#define CONFIG_FSL_DIU_FB
 
-#ifdef CONFIG_VIDEO
+#ifdef CONFIG_FSL_DIU_FB
+#define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_CCSRBAR + 0x2c000)
+#define CONFIG_VIDEO
 #define CONFIG_CMD_BMP
 #define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
 #define CONFIG_VGA_AS_SINGLE_DEVICE
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO
@@ -49,6 +52,7 @@
 #define CONFIG_PCIE1		1	/* PCIe 1 connected to ULI bridge */
 #define CONFIG_PCIE2		1	/* PCIe 2 connected to slot */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
@@ -88,10 +92,8 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0x0
 #define CONFIG_SYS_CCSRBAR_PHYS		CONFIG_SYS_CCSRBAR_PHYS_LOW
 
-#define CONFIG_SYS_DIU_ADDR		(CONFIG_SYS_CCSRBAR+0x2c000)
-
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD for DDR */
 #define CONFIG_DDR_SPD
@@ -108,7 +110,7 @@
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
-#define SPD_EEPROM_ADDRESS1	0x51	/* CTLR 0 DIMM 0 */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
 
 /* These are used when DDR doesn't use SPD.  */
 #define CONFIG_SYS_SDRAM_SIZE	256		/* DDR is 256MB */
@@ -213,10 +215,9 @@
 #else
 #define CONFIG_SYS_INIT_RAM_ADDR	0xe4000000	/* Initial RAM address */
 #endif
-#define CONFIG_SYS_INIT_RAM_END	0x4000		/* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_SIZE	128		/* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
@@ -237,9 +238,6 @@
 
 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER
-#ifdef	CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
 
 /*
  * Pass open firmware flat tree to kernel
@@ -255,13 +253,12 @@
 /*
  * I2C
  */
-#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
 
 /*
  * General PCI
@@ -277,6 +274,7 @@
 #define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
 
 /* controller 1, Base address 0xa000 */
+#define CONFIG_SYS_PCIE1_NAME		"ULI"
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xa0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
@@ -285,6 +283,7 @@
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00100000	/* 1M */
 
 /* controller 2, Base Address 0x9000 */
+#define CONFIG_SYS_PCIE2_NAME		"Slot 1"
 #define CONFIG_SYS_PCIE2_MEM_BUS	0x90000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
@@ -297,14 +296,11 @@
 
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 
-#define CONFIG_NET_MULTI
-#define CONFIG_CMD_NET
 #define CONFIG_PCI_PNP		/* do pci plug-and-play */
 #define CONFIG_CMD_REGINFO
 
 #define CONFIG_ULI526X
 #ifdef CONFIG_ULI526X
-#define CONFIG_ETHADDR   00:E0:0C:00:00:01
 #endif
 
 /************************************************************
@@ -329,6 +325,7 @@
 #define CONFIG_SCSI_AHCI
 
 #ifdef CONFIG_SCSI_AHCI
+#define CONFIG_LIBATA
 #define CONFIG_SATA_ULI5288
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID	4
 #define CONFIG_SYS_SCSI_MAX_LUN	1
@@ -472,16 +469,10 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 
-#if defined(CONFIG_SYS_RAMBOOT)
-#undef CONFIG_CMD_SAVEENV
-#endif
-
 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SCSI
@@ -493,16 +484,12 @@
 #define CONFIG_WATCHDOG			/* watchdog enabled */
 #define CONFIG_SYS_WATCHDOG_FREQ	5000	/* Feed interval, 5s */
 
-/*DIU Configuration*/
-#define DIU_CONNECT_TO_DVI		/* DIU controller connects to DVI encoder*/
-
 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
@@ -513,7 +500,6 @@
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
@@ -522,17 +508,8 @@
  */
 #define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02		/* Software reboot */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 
 /*
@@ -541,8 +518,8 @@
 #define CONFIG_IPADDR		192.168.1.100
 
 #define CONFIG_HOSTNAME		unknown
-#define CONFIG_ROOTPATH		/opt/nfsroot
-#define CONFIG_BOOTFILE		uImage
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
 #define CONFIG_UBOOTPATH	8610hpcd/u-boot.bin
 
 #define CONFIG_SERVERIP		192.168.1.1
@@ -605,62 +582,63 @@
 
 #ifdef ENV_DEBUG
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
- "netdev=eth0\0"						\
- "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
- "tftpflash=tftpboot $loadaddr $uboot; "			\
-	"protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
-	"erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "		\
-	"cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; "	\
-	"protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
-	"cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0"	\
- "consoledev=ttyS0\0"						\
- "ramdiskaddr=2000000\0"					\
- "ramdiskfile=8610hpcd/ramdisk.uboot\0"				\
- "fdtaddr=c00000\0"						\
- "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"				\
- "bdev=sda3\0"					\
- "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
- "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
- "maxcpus=1"	\
- "eoi=mw e00400b0 0\0"						\
- "iack=md e00400a0 1\0"						\
- "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
+"netdev=eth0\0"							\
+"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
+"tftpflash=tftpboot $loadaddr $uboot; "				\
+	"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
+		" +$filesize; "	\
+	"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
+		" +$filesize; "	\
+	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
+		" $filesize; "	\
+	"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
+		" +$filesize; "	\
+	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
+		" $filesize\0"	\
+"consoledev=ttyS0\0"						\
+"ramdiskaddr=2000000\0"					\
+"ramdiskfile=8610hpcd/ramdisk.uboot\0"				\
+"fdtaddr=c00000\0"						\
+"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"				\
+"bdev=sda3\0"					\
+"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
+"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
+"maxcpus=1"	\
+"eoi=mw e00400b0 0\0"						\
+"iack=md e00400a0 1\0"						\
+"ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
 	"md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
 	"md ${a}f00 5\0" \
- "ddr1regs=setenv a e0002; run ddrreg\0" \
- "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
+"ddr1regs=setenv a e0002; run ddrreg\0" \
+"gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
 	"md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
 	"md ${a}e60 1; md ${a}ef0 1d\0" \
- "guregs=setenv a e00e0; run gureg\0" \
- "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
- "mcmregs=setenv a e0001; run mcmreg\0" \
- "diuregs=md e002c000 1d\0" \
- "dium=mw e002c01c\0" \
- "diuerr=md e002c014 1\0" \
- "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 debug\0" \
- "monitor=0-DVI\0" \
- "pmregs=md e00e1000 2b\0" \
- "lawregs=md e0000c08 4b\0" \
- "lbcregs=md e0005000 36\0" \
- "dma0regs=md e0021100 12\0" \
- "dma1regs=md e0021180 12\0" \
- "dma2regs=md e0021200 12\0" \
- "dma3regs=md e0021280 12\0" \
+"guregs=setenv a e00e0; run gureg\0" \
+"mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
+"mcmregs=setenv a e0001; run mcmreg\0" \
+"diuregs=md e002c000 1d\0" \
+"dium=mw e002c01c\0" \
+"diuerr=md e002c014 1\0" \
+"pmregs=md e00e1000 2b\0" \
+"lawregs=md e0000c08 4b\0" \
+"lbcregs=md e0005000 36\0" \
+"dma0regs=md e0021100 12\0" \
+"dma1regs=md e0021180 12\0" \
+"dma2regs=md e0021200 12\0" \
+"dma3regs=md e0021280 12\0" \
  PCI_ENV \
  PCIE_ENV \
  DMA_ENV
 #else
-#define CONFIG_EXTRA_ENV_SETTINGS                               \
- "netdev=eth0\0"                                                \
- "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"                         \
- "consoledev=ttyS0\0"                                           \
- "ramdiskaddr=2000000\0"                                        \
- "ramdiskfile=8610hpcd/ramdisk.uboot\0"                         \
- "fdtaddr=c00000\0"                                             \
- "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"                          \
- "bdev=sda3\0"							\
- "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0\0"\
- "monitor=0-DVI\0"
+#define CONFIG_EXTRA_ENV_SETTINGS				\
+	"netdev=eth0\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
+	"consoledev=ttyS0\0"					\
+	"ramdiskaddr=2000000\0"					\
+	"ramdiskfile=8610hpcd/ramdisk.uboot\0"			\
+	"fdtaddr=c00000\0"					\
+	"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"			\
+	"bdev=sda3\0"
 #endif
 
 #define CONFIG_NFSBOOTCOMMAND					\