X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8572DS.h;h=64f5c4b750ecb1de77156ba7910348073d9570ac;hb=cb32ed1fc298875845f166d326a3f2704a0d5364;hp=c2ed961cfd7d392de60f63295e8cc1d35557da4a;hpb=1c9aa76bf9013069e24258f46f4687c9f98a02d6;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
index c2ed961..64f5c4b 100644
--- a/include/configs/MPC8572DS.h
+++ b/include/configs/MPC8572DS.h
@@ -36,12 +36,14 @@
 #define CONFIG_MP		1	/* support multiple processors */
 #define CONFIG_NUM_CPUS		2	/* Number of CPUs in the system */
 
+#define CONFIG_FSL_ELBC		1	/* Has Enhanced localbus controller */
 #define CONFIG_PCI		1	/* Enable PCI/PCIE */
 #define CONFIG_PCIE1		1	/* PCIE controler 1 (slot 1) */
 #define CONFIG_PCIE2		1	/* PCIE controler 2 (slot 2) */
 #define CONFIG_PCIE3		1	/* PCIE controler 3 (ULI bridge) */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
 #define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
 
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
@@ -61,7 +63,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #endif
 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
 #define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk(0) /* ddrclk for MPC85xx */
-#define CONFIG_ICS307_REFCLK_HZ	33333333  /* ICS307 clock chip ref freq */
+#define CONFIG_ICS307_REFCLK_HZ	33333000  /* ICS307 clock chip ref freq */
 #define CONFIG_GET_CLK_FROM_ICS307	  /* decode sysclk and ddrclk freq
 					     from ICS307 instead of switches */
 
@@ -70,10 +72,14 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  */
 #define CONFIG_L2_CACHE			/* toggle L2 cache */
 #define CONFIG_BTB			/* toggle branch predition */
-#define CONFIG_ADDR_STREAMING		/* toggle addr streaming */
 
 #define CONFIG_ENABLE_36BIT_PHYS	1
 
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP			1
+#define CONFIG_SYS_NUM_ADDR_MAP		16	/* number of TLB1 entries */
+#endif
+
 #define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x7fffffff
 #define CONFIG_PANIC_HANG	/* do not reset board on panic */
@@ -84,7 +90,11 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  */
 #define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
 #define CONFIG_SYS_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS		0xfffe00000ull	/* physical addr of CCSRBAR */
+#else
 #define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
+#endif
 #define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
 
 #define CONFIG_SYS_PCIE3_ADDR		(CONFIG_SYS_CCSRBAR+0x8000)
@@ -92,12 +102,15 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_PCIE1_ADDR		(CONFIG_SYS_CCSRBAR+0xa000)
 
 /* DDR Setup */
+#define CONFIG_SYS_DDR_TLB_START 9
+#define CONFIG_VERY_BIG_RAM
 #define CONFIG_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 #undef CONFIG_DDR_DLL
 
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef
 
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
@@ -113,38 +126,28 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define SPD_EEPROM_ADDRESS2	0x52	/* CTLR 1 DIMM 0 */
 
 /* These are used when DDR doesn't use SPD.  */
-#define CONFIG_SYS_SDRAM_SIZE		256		/* DDR is 256MB */
-#define CONFIG_SYS_DDR_CS0_BNDS	0x0000001F
-#define CONFIG_SYS_DDR_CS0_CONFIG	0x80010102	/* Enable, no interleaving */
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-#define CONFIG_SYS_DDR_TIMING_0	0x00260802
-#define CONFIG_SYS_DDR_TIMING_1	0x3935d322
-#define CONFIG_SYS_DDR_TIMING_2	0x14904cc8
-#define CONFIG_SYS_DDR_MODE_1		0x00480432
+#define CONFIG_SYS_SDRAM_SIZE		512		/* DDR is 512MB */
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000001F
+#define CONFIG_SYS_DDR_CS0_CONFIG	0x80010202	/* Enable, no interleaving */
+#define CONFIG_SYS_DDR_TIMING_3		0x00020000
+#define CONFIG_SYS_DDR_TIMING_0		0x00260802
+#define CONFIG_SYS_DDR_TIMING_1		0x626b2634
+#define CONFIG_SYS_DDR_TIMING_2		0x062874cf
+#define CONFIG_SYS_DDR_MODE_1		0x00440462
 #define CONFIG_SYS_DDR_MODE_2		0x00000000
-#define CONFIG_SYS_DDR_INTERVAL	0x06180100
+#define CONFIG_SYS_DDR_INTERVAL		0x0c300100
 #define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
-#define CONFIG_SYS_DDR_CLK_CTRL	0x03800000
-#define CONFIG_SYS_DDR_OCD_CTRL	0x00000000
+#define CONFIG_SYS_DDR_CLK_CTRL		0x00800000
+#define CONFIG_SYS_DDR_OCD_CTRL		0x00000000
 #define CONFIG_SYS_DDR_OCD_STATUS	0x00000000
-#define CONFIG_SYS_DDR_CONTROL		0xC3008000	/* Type = DDR2 */
-#define CONFIG_SYS_DDR_CONTROL2	0x04400010
+#define CONFIG_SYS_DDR_CONTROL		0xc3000008	/* Type = DDR2 */
+#define CONFIG_SYS_DDR_CONTROL2		0x24400000
 
 #define CONFIG_SYS_DDR_ERR_INT_EN	0x0000000d
 #define CONFIG_SYS_DDR_ERR_DIS		0x00000000
 #define CONFIG_SYS_DDR_SBE		0x00010000
 
 /*
- * FIXME: Not used in fixed_sdram function
- */
-#define CONFIG_SYS_DDR_MODE		0x00000022
-#define CONFIG_SYS_DDR_CS1_BNDS	0x00000000
-#define CONFIG_SYS_DDR_CS2_BNDS	0x00000FFF	/* Not done */
-#define CONFIG_SYS_DDR_CS3_BNDS	0x00000FFF	/* Not done */
-#define CONFIG_SYS_DDR_CS4_BNDS	0x00000FFF	/* Not done */
-#define CONFIG_SYS_DDR_CS5_BNDS	0x00000FFF	/* Not done */
-
-/*
  * Make sure required options are set
  */
 #ifndef CONFIG_SPD_EEPROM
@@ -167,6 +170,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * Localbus non-cacheable
  * 0xe000_0000	0xe80f_ffff	Promjet/free		128M non-cacheable
  * 0xe800_0000	0xefff_ffff	FLASH			128M non-cacheable
+ * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
  * 0xffdf_0000	0xffdf_7fff	PIXIS			32K non-cacheable TLB0
  * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
  * 0xffe0_0000	0xffef_ffff	CCSR			1M non-cacheable
@@ -176,14 +180,19 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * Local Bus Definitions
  */
 #define CONFIG_SYS_FLASH_BASE		0xe0000000	/* start of FLASH 128M */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS	0xfe0000000ull
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+#endif
 
-#define CONFIG_SYS_BR0_PRELIM		0xe8001001
-#define CONFIG_SYS_OR0_PRELIM		0xf8000ff7
+#define CONFIG_SYS_BR0_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR0_PRELIM	0xf8000ff7
 
-#define CONFIG_SYS_BR1_PRELIM		0xe0001001
-#define CONFIG_SYS_OR1_PRELIM		0xf8000ff7
+#define CONFIG_SYS_BR1_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM	0xf8000ff7
 
-#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE + 0x8000000, CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
 
@@ -204,8 +213,13 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 
 #define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
 #define PIXIS_BASE	0xffdf0000	/* PIXIS registers */
+#ifdef CONFIG_PHYS_64BIT
+#define PIXIS_BASE_PHYS	0xfffdf0000ull
+#else
+#define PIXIS_BASE_PHYS	PIXIS_BASE
+#endif
 
-#define CONFIG_SYS_BR3_PRELIM	(PIXIS_BASE | 0x0801)	/* port size 8bit */
+#define CONFIG_SYS_BR3_PRELIM	(BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
 #define CONFIG_SYS_OR3_PRELIM		0xffffeff7	/* 32KB but only 4k mapped */
 
 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
@@ -223,6 +237,11 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
 #define PIXIS_VCORE0	 	0x14	/* VELA VCORE0 Register */
 #define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
+#define PIXIS_VBOOT_LBMAP	0xc0	/* VBOOT - CFG_LBMAP */
+#define PIXIS_VBOOT_LBMAP_NOR0	0x00	/* cfg_lbmap - boot from NOR 0 */
+#define PIXIS_VBOOT_LBMAP_PJET	0x01	/* cfg_lbmap - boot from projet */
+#define PIXIS_VBOOT_LBMAP_NAND	0x02	/* cfg_lbmap - boot from NAND */
+#define PIXIS_VBOOT_LBMAP_NOR1	0x03	/* cfg_lbmap - boot from NOR 1 */
 #define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
 #define PIXIS_VSPEED2		0x19	/* VELA VSpeed 2 */
@@ -239,9 +258,23 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
 #define CONFIG_SYS_PIXIS_VBOOT_MASK	0xc0
+#define PIXIS_VSPEED2_TSEC1SER	0x8
+#define PIXIS_VSPEED2_TSEC2SER	0x4
+#define PIXIS_VSPEED2_TSEC3SER	0x2
+#define PIXIS_VSPEED2_TSEC4SER	0x1
+#define PIXIS_VCFGEN1_TSEC1SER	0x20
+#define PIXIS_VCFGEN1_TSEC2SER	0x20
+#define PIXIS_VCFGEN1_TSEC3SER	0x20
+#define PIXIS_VCFGEN1_TSEC4SER	0x20
+#define PIXIS_VSPEED2_MASK	(PIXIS_VSPEED2_TSEC1SER \
+					| PIXIS_VSPEED2_TSEC2SER \
+					| PIXIS_VSPEED2_TSEC3SER \
+					| PIXIS_VSPEED2_TSEC4SER)
+#define PIXIS_VCFGEN1_MASK	(PIXIS_VCFGEN1_TSEC1SER \
+					| PIXIS_VCFGEN1_TSEC2SER \
+					| PIXIS_VCFGEN1_TSEC3SER \
+					| PIXIS_VCFGEN1_TSEC4SER)
 
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_END	0x00004000	/* End of used area in RAM */
@@ -253,6 +286,61 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
 
+#define CONFIG_SYS_NAND_BASE		0xffa00000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS	0xfffa00000ull
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+#endif
+#define CONFIG_SYS_NAND_BASE_LIST     { CONFIG_SYS_NAND_BASE,\
+				CONFIG_SYS_NAND_BASE + 0x40000, \
+				CONFIG_SYS_NAND_BASE + 0x80000,\
+				CONFIG_SYS_NAND_BASE + 0xC0000}
+#define CONFIG_SYS_MAX_NAND_DEVICE    4
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND		1
+#define CONFIG_NAND_FSL_ELBC	1
+#define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
+
+/* NAND flash config */
+#define CONFIG_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+			       | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
+			       | BR_PS_8	       /* Port Size = 8 bit */ \
+			       | BR_MS_FCM	       /* MSEL = FCM */ \
+			       | BR_V)		       /* valid */
+#define CONFIG_NAND_OR_PRELIM  (0xFFFC0000	      /* length 256K */ \
+			       | OR_FCM_PGS	       /* Large Page*/ \
+			       | OR_FCM_CSCT \
+			       | OR_FCM_CST \
+			       | OR_FCM_CHT \
+			       | OR_FCM_SCY_1 \
+			       | OR_FCM_TRLX \
+			       | OR_FCM_EHTR)
+
+#define CONFIG_SYS_BR2_PRELIM  CONFIG_NAND_BR_PRELIM  /* NAND Base Address */
+#define CONFIG_SYS_OR2_PRELIM  CONFIG_NAND_OR_PRELIM  /* NAND Options */
+
+#define CONFIG_SYS_BR4_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x40000))\
+			       | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
+			       | BR_PS_8	       /* Port Size = 8 bit */ \
+			       | BR_MS_FCM	       /* MSEL = FCM */ \
+			       | BR_V)		       /* valid */
+#define CONFIG_SYS_OR4_PRELIM  CONFIG_NAND_OR_PRELIM	 /* NAND Options */
+#define CONFIG_SYS_BR5_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x80000))\
+			       | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
+			       | BR_PS_8	       /* Port Size = 8 bit */ \
+			       | BR_MS_FCM	       /* MSEL = FCM */ \
+			       | BR_V)		       /* valid */
+#define CONFIG_SYS_OR5_PRELIM  CONFIG_NAND_OR_PRELIM	 /* NAND Options */
+
+#define CONFIG_SYS_BR6_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0xc0000))\
+			       | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
+			       | BR_PS_8	       /* Port Size = 8 bit */ \
+			       | BR_MS_FCM	       /* MSEL = FCM */ \
+			       | BR_V)		       /* valid */
+#define CONFIG_SYS_OR6_PRELIM  CONFIG_NAND_OR_PRELIM	 /* NAND Options */
+
+
 /* Serial Port - controlled on board with jumper J8
  * open - index 2
  * shorted - index 1
@@ -295,7 +383,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
 #undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
 #define CONFIG_SYS_I2C_SLAVE		0x7F
@@ -319,39 +406,67 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 
-/* PCI view of System Memory */
-#define CONFIG_SYS_PCI_MEMORY_BUS	0x00000000
-#define CONFIG_SYS_PCI_MEMORY_PHYS	0x00000000
-#define CONFIG_SYS_PCI_MEMORY_SIZE	0x80000000
-
 /* controller 3, direct to uli, tgtid 3, Base address 8000 */
-#define CONFIG_SYS_PCIE3_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	CONFIG_SYS_PCIE3_MEM_BASE
+#define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0x80000000
+#endif
 #define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE3_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
+#define CONFIG_SYS_PCIE3_IO_BUS	0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xfffc00000ull
+#else
 #define CONFIG_SYS_PCIE3_IO_PHYS	0xffc00000
+#endif
 #define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 2, Slot 2, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_MEM_BASE	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BASE
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
+#endif
 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS	0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xfffc10000ull
+#else
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
+#endif
 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 1, Slot 1, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_MEM_BASE	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc40000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc0000000
+#endif
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
+#define CONFIG_SYS_PCIE1_IO_BUS	0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xfffc20000ull
+#else
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xffc20000
+#endif
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
 
 #if defined(CONFIG_PCI)
 
 /*PCIE video card used*/
-#define VIDEO_IO_OFFSET		CONFIG_SYS_PCIE1_IO_PHYS
+#define VIDEO_IO_OFFSET		CONFIG_SYS_PCIE1_IO_VIRT
 
 /* video */
 #define CONFIG_VIDEO
@@ -374,15 +489,9 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #undef CONFIG_TULIP
 #undef CONFIG_RTL8139
 
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x)		(x)
-#define _IO_BASE	0x00000000
-#endif
-
 #ifndef CONFIG_PCI_PNP
-	#define PCI_ENET0_IOADDR	CONFIG_SYS_PCIE3_IO_BASE
-	#define PCI_ENET0_MEMADDR	CONFIG_SYS_PCIE3_IO_BASE
+	#define PCI_ENET0_IOADDR	CONFIG_SYS_PCIE3_IO_BUS
+	#define PCI_ENET0_MEMADDR	CONFIG_SYS_PCIE3_IO_BUS
 	#define PCI_IDSEL_NUMBER	0x11	/* IDSEL = AD11 */
 #endif
 
@@ -418,6 +527,14 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_TSEC4	1
 #define CONFIG_TSEC4_NAME	"eTSEC4"
 
+#define CONFIG_PIXIS_SGMII_CMD
+#define CONFIG_FSL_SGMII_RISER	1
+#define SGMII_RISER_PHY_OFFSET	0x1c
+
+#ifdef CONFIG_FSL_SGMII_RISER
+#define CONFIG_SYS_TBIPA_VALUE		0x10 /* avoid conflict with eTSEC4 paddr */
+#endif
+
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC3_PHY_ADDR		2
@@ -445,7 +562,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #if CONFIG_SYS_MONITOR_BASE > 0xfff80000
 #define CONFIG_ENV_ADDR		0xfff80000
 #else
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x70000)
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #endif
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
@@ -495,10 +612,10 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 16 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
 
 /*
  * Internal Definitions
@@ -549,6 +666,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_BAUDRATE	115200
 
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
+ "memctl_intlv_ctl=2\0"						\
  "netdev=eth0\0"						\
  "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
  "tftpflash=tftpboot $loadaddr $uboot; "			\