X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8572DS.h;h=64f5c4b750ecb1de77156ba7910348073d9570ac;hb=cb32ed1fc298875845f166d326a3f2704a0d5364;hp=87b10116d1d296308588e161ae0eee788afd971d;hpb=1f3ba317a5c5f3a7aabf580fddc211f4bb5a4540;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 87b1011..64f5c4b 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -36,12 +36,14 @@ #define CONFIG_MP 1 /* support multiple processors */ #define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ +#define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */ #define CONFIG_PCI 1 /* Enable PCI/PCIE */ #define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ #define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ #define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ @@ -61,7 +63,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #endif #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ -#define CONFIG_ICS307_REFCLK_HZ 33333333 /* ICS307 clock chip ref freq */ +#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ #define CONFIG_GET_CLK_FROM_ICS307 /* decode sysclk and ddrclk freq from ICS307 instead of switches */ @@ -70,79 +72,80 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ #define CONFIG_ENABLE_36BIT_PHYS 1 -#define CFG_MEMTEST_START 0x00000000 /* memtest works on */ -#define CFG_MEMTEST_END 0x7fffffff +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_ADDR_MAP 1 +#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ +#endif + +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x7fffffff #define CONFIG_PANIC_HANG /* do not reset board on panic */ /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ -#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */ +#else +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#endif +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ -#define CFG_PCIE3_ADDR (CFG_CCSRBAR+0x8000) -#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000) -#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000) +#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR+0x8000) +#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) +#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) /* DDR Setup */ +#define CONFIG_SYS_DDR_TLB_START 9 +#define CONFIG_VERY_BIG_RAM #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ #define CONFIG_DDR_SPD #undef CONFIG_DDR_DLL +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER #define CONFIG_MEM_INIT_VALUE 0xDeadBeef -#define CFG_DDR_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_NUM_DDR_CONTROLLERS 2 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 /* I2C addresses of SPD EEPROMs */ -#define CFG_SPD_BUS_NUM 1 /* SPD EEPROMS locate on I2C bus 1 */ +#define CONFIG_SYS_SPD_BUS_NUM 1 /* SPD EEPROMS locate on I2C bus 1 */ #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ #define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 1 DIMM 0 */ /* These are used when DDR doesn't use SPD. */ -#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */ -#define CFG_DDR_CS0_BNDS 0x0000001F -#define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ -#define CFG_DDR_TIMING_3 0x00000000 -#define CFG_DDR_TIMING_0 0x00260802 -#define CFG_DDR_TIMING_1 0x3935d322 -#define CFG_DDR_TIMING_2 0x14904cc8 -#define CFG_DDR_MODE_1 0x00480432 -#define CFG_DDR_MODE_2 0x00000000 -#define CFG_DDR_INTERVAL 0x06180100 -#define CFG_DDR_DATA_INIT 0xdeadbeef -#define CFG_DDR_CLK_CTRL 0x03800000 -#define CFG_DDR_OCD_CTRL 0x00000000 -#define CFG_DDR_OCD_STATUS 0x00000000 -#define CFG_DDR_CONTROL 0xC3008000 /* Type = DDR2 */ -#define CFG_DDR_CONTROL2 0x04400010 - -#define CFG_DDR_ERR_INT_EN 0x0000000d -#define CFG_DDR_ERR_DIS 0x00000000 -#define CFG_DDR_SBE 0x00010000 - -/* - * FIXME: Not used in fixed_sdram function - */ -#define CFG_DDR_MODE 0x00000022 -#define CFG_DDR_CS1_BNDS 0x00000000 -#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */ -#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */ -#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */ -#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */ +#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */ +#define CONFIG_SYS_DDR_TIMING_3 0x00020000 +#define CONFIG_SYS_DDR_TIMING_0 0x00260802 +#define CONFIG_SYS_DDR_TIMING_1 0x626b2634 +#define CONFIG_SYS_DDR_TIMING_2 0x062874cf +#define CONFIG_SYS_DDR_MODE_1 0x00440462 +#define CONFIG_SYS_DDR_MODE_2 0x00000000 +#define CONFIG_SYS_DDR_INTERVAL 0x0c300100 +#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef +#define CONFIG_SYS_DDR_CLK_CTRL 0x00800000 +#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 +#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 +#define CONFIG_SYS_DDR_CONTROL 0xc3000008 /* Type = DDR2 */ +#define CONFIG_SYS_DDR_CONTROL2 0x24400000 + +#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d +#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 +#define CONFIG_SYS_DDR_SBE 0x00010000 /* * Make sure required options are set @@ -167,6 +170,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); * Localbus non-cacheable * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable + * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable @@ -175,38 +179,48 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* * Local Bus Definitions */ -#define CFG_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ +#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull +#else +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE +#endif -#define CFG_BR0_PRELIM 0xe8001001 -#define CFG_OR0_PRELIM 0xf8000ff7 +#define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V) +#define CONFIG_SYS_OR0_PRELIM 0xf8000ff7 -#define CFG_BR1_PRELIM 0xe0001001 -#define CFG_OR1_PRELIM 0xf8000ff7 +#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) +#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7 -#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE + 0x8000000, CFG_FLASH_BASE} -#define CFG_FLASH_QUIET_TEST +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_SYS_FLASH_QUIET_TEST #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ -#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ -#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CONFIG_FLASH_CFI_DRIVER -#define CFG_FLASH_CFI -#define CFG_FLASH_EMPTY_INFO -#define CFG_FLASH_AMD_CHECK_DQ7 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ +#ifdef CONFIG_PHYS_64BIT +#define PIXIS_BASE_PHYS 0xfffdf0000ull +#else +#define PIXIS_BASE_PHYS PIXIS_BASE +#endif -#define CFG_BR3_PRELIM (PIXIS_BASE | 0x0801) /* port size 8bit */ -#define CFG_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ +#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V) +#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ #define PIXIS_ID 0x0 /* Board ID at offset 0 */ #define PIXIS_VER 0x1 /* Board version at offset 1 */ @@ -223,6 +237,11 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ #define PIXIS_VCORE0 0x14 /* VELA VCORE0 Register */ #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ +#define PIXIS_VBOOT_LBMAP 0xc0 /* VBOOT - CFG_LBMAP */ +#define PIXIS_VBOOT_LBMAP_NOR0 0x00 /* cfg_lbmap - boot from NOR 0 */ +#define PIXIS_VBOOT_LBMAP_PJET 0x01 /* cfg_lbmap - boot from projet */ +#define PIXIS_VBOOT_LBMAP_NAND 0x02 /* cfg_lbmap - boot from NAND */ +#define PIXIS_VBOOT_LBMAP_NOR1 0x03 /* cfg_lbmap - boot from NOR 1 */ #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ #define PIXIS_VSPEED2 0x19 /* VELA VSpeed 2 */ @@ -238,20 +257,89 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* old pixis referenced names */ #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ -#define CFG_PIXIS_VBOOT_MASK 0xc0 - -/* define to use L1 as initial stack */ -#define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ -#define CFG_INIT_RAM_END 0x00004000 /* End of used area in RAM */ - -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_PIXIS_VBOOT_MASK 0xc0 +#define PIXIS_VSPEED2_TSEC1SER 0x8 +#define PIXIS_VSPEED2_TSEC2SER 0x4 +#define PIXIS_VSPEED2_TSEC3SER 0x2 +#define PIXIS_VSPEED2_TSEC4SER 0x1 +#define PIXIS_VCFGEN1_TSEC1SER 0x20 +#define PIXIS_VCFGEN1_TSEC2SER 0x20 +#define PIXIS_VCFGEN1_TSEC3SER 0x20 +#define PIXIS_VCFGEN1_TSEC4SER 0x20 +#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER \ + | PIXIS_VSPEED2_TSEC2SER \ + | PIXIS_VSPEED2_TSEC3SER \ + | PIXIS_VSPEED2_TSEC4SER) +#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER \ + | PIXIS_VCFGEN1_TSEC2SER \ + | PIXIS_VCFGEN1_TSEC3SER \ + | PIXIS_VCFGEN1_TSEC4SER) + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +#define CONFIG_SYS_NAND_BASE 0xffa00000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull +#else +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#endif +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE,\ + CONFIG_SYS_NAND_BASE + 0x40000, \ + CONFIG_SYS_NAND_BASE + 0x80000,\ + CONFIG_SYS_NAND_BASE + 0xC0000} +#define CONFIG_SYS_MAX_NAND_DEVICE 4 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND 1 +#define CONFIG_NAND_FSL_ELBC 1 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +/* NAND flash config */ +#define CONFIG_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | (2< " +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* @@ -283,8 +371,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CFG_64BIT_VSPRINTF 1 -#define CFG_64BIT_STRTOUL 1 +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 /* new uImage format support */ #define CONFIG_FIT 1 @@ -295,52 +383,90 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_EEPROM_ADDR 0x57 -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0,0x29} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3000 -#define CFG_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}}/* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * I2C2 EEPROM + */ +#define CONFIG_ID_EEPROM +#ifdef CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#endif +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_BUS_NUM 1 /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ -/* PCI view of System Memory */ -#define CFG_PCI_MEMORY_BUS 0x00000000 -#define CFG_PCI_MEMORY_PHYS 0x00000000 -#define CFG_PCI_MEMORY_SIZE 0x80000000 - /* controller 3, direct to uli, tgtid 3, Base address 8000 */ -#define CFG_PCIE3_MEM_BASE 0x80000000 -#define CFG_PCIE3_MEM_PHYS CFG_PCIE3_MEM_BASE -#define CFG_PCIE3_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCIE3_IO_BASE 0x00000000 -#define CFG_PCIE3_IO_PHYS 0xffc00000 -#define CFG_PCIE3_IO_SIZE 0x00010000 /* 64k */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull +#else +#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000 +#endif +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull +#else +#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000 +#endif +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ /* controller 2, Slot 2, tgtid 2, Base address 9000 */ -#define CFG_PCIE2_MEM_BASE 0xa0000000 -#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE -#define CFG_PCIE2_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCIE2_IO_BASE 0x00000000 -#define CFG_PCIE2_IO_PHYS 0xffc10000 -#define CFG_PCIE2_IO_SIZE 0x00010000 /* 64k */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull +#else +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#endif +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull +#else +#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 +#endif +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ /* controller 1, Slot 1, tgtid 1, Base address a000 */ -#define CFG_PCIE1_MEM_BASE 0xc0000000 -#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE -#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCIE1_IO_BASE 0x00000000 -#define CFG_PCIE1_IO_PHYS 0xffc20000 -#define CFG_PCIE1_IO_SIZE 0x00010000 /* 64k */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull +#else +#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 +#endif +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull +#else +#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 +#endif +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ #if defined(CONFIG_PCI) /*PCIE video card used*/ -#define VIDEO_IO_OFFSET CFG_PCIE1_IO_PHYS +#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT /* video */ #define CONFIG_VIDEO @@ -353,7 +479,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_ATI_RADEON_FB #define CONFIG_VIDEO_LOGO /*#define CONFIG_CONSOLE_CURSOR*/ -#define CFG_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET #endif #define CONFIG_NET_MULTI @@ -363,15 +489,9 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #undef CONFIG_TULIP #undef CONFIG_RTL8139 -#ifdef CONFIG_RTL8139 -/* This macro is used by RTL8139 but not defined in PPC architecture */ -#define KSEG1ADDR(x) (x) -#define _IO_BASE 0x00000000 -#endif - #ifndef CONFIG_PCI_PNP - #define PCI_ENET0_IOADDR CFG_PCIE3_IO_BASE - #define PCI_ENET0_MEMADDR CFG_PCIE3_IO_BASE + #define PCI_ENET0_IOADDR CONFIG_SYS_PCIE3_IO_BUS + #define PCI_ENET0_MEMADDR CONFIG_SYS_PCIE3_IO_BUS #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ #endif @@ -381,10 +501,10 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #ifdef CONFIG_SCSI_AHCI #define CONFIG_SATA_ULI5288 -#define CFG_SCSI_MAX_SCSI_ID 4 -#define CFG_SCSI_MAX_LUN 1 -#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) -#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) +#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE #endif /* SCSI */ #endif /* CONFIG_PCI */ @@ -407,6 +527,14 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_TSEC4 1 #define CONFIG_TSEC4_NAME "eTSEC4" +#define CONFIG_PIXIS_SGMII_CMD +#define CONFIG_FSL_SGMII_RISER 1 +#define SGMII_RISER_PHY_OFFSET 0x1c + +#ifdef CONFIG_FSL_SGMII_RISER +#define CONFIG_SYS_TBIPA_VALUE 0x10 /* avoid conflict with eTSEC4 paddr */ +#endif + #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC3_PHY_ADDR 2 @@ -431,16 +559,16 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); * Environment */ #define CONFIG_ENV_IS_IN_FLASH 1 -#if CFG_MONITOR_BASE > 0xfff80000 +#if CONFIG_SYS_MONITOR_BASE > 0xfff80000 #define CONFIG_ENV_ADDR 0xfff80000 #else -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + 0x70000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) #endif #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * Command line configuration. @@ -452,6 +580,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_CMD_I2C #define CONFIG_CMD_MII #define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_SETEXPR #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI @@ -466,26 +596,26 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 16 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ /* * Internal Definitions @@ -536,6 +666,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_BAUDRATE 115200 #define CONFIG_EXTRA_ENV_SETTINGS \ + "memctl_intlv_ctl=2\0" \ "netdev=eth0\0" \ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ "tftpflash=tftpboot $loadaddr $uboot; " \