X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8568MDS.h;h=d6171b4683c05726b20044b8957ddcb850bea655;hb=d98b0523cfaaedeecb263b15c121c0727b0d80b9;hp=0cc2d474284149e8aada3771c19cd6646db33038;hpb=b6c208ab1ebc2ac01e0029b8456210617ff67156;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 0cc2d47..d6171b4 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -33,6 +33,8 @@
 #define CONFIG_MPC8568		1	/* MPC8568 specific */
 #define CONFIG_MPC8568MDS	1	/* MPC8568MDS board specific */
 
+#define	CONFIG_SYS_TEXT_BASE	0xfff80000
+
 #define CONFIG_PCI		1	/* Enable PCI/PCIE */
 #define CONFIG_PCI1		1	/* PCI controller */
 #define CONFIG_PCIE1		1	/* PCIE controller */
@@ -75,9 +77,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
 #define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
 
-#define CONFIG_SYS_PCI1_ADDR           (CONFIG_SYS_CCSRBAR+0x8000)
-#define CONFIG_SYS_PCIE1_ADDR          (CONFIG_SYS_CCSRBAR+0xa000)
-
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -157,7 +156,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
 
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
@@ -247,7 +246,6 @@ extern unsigned long get_clock_freq(void);
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX		1
-#undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
@@ -316,7 +314,7 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_UEC_ETH
 #ifndef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME         "FSL UEC0"
+#define CONFIG_ETHPRIME         "UEC0"
 #endif
 #define CONFIG_PHY_MODE_NEED_CHANGE
 #define CONFIG_eTSEC_MDIO_BUS
@@ -434,7 +432,8 @@ extern unsigned long get_clock_freq(void);
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
-#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
 #define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
@@ -454,14 +453,6 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02		/* Software reboot */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */