X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8568MDS.h;h=3a405d46dd6a12af7b853416c7cf6ee2eead657a;hb=14d0a02a168b36e87665b8d7f42fa3e88263d26d;hp=77224d98e7b3f86862c8d9295f3fbb6893b4044f;hpb=dfc91c33957c95da34e3888dc87912d5c15a7603;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 77224d9..3a405d4 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -44,13 +44,6 @@
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
-/*
- * When initializing flash, if we cannot find the manufacturer ID,
- * assume this is the AMD flash associated with the MDS board.
- * This allows booting from a promjet.
- */
-#define CONFIG_ASSUME_AMD_FLASH
-
 #ifndef __ASSEMBLY__
 extern unsigned long get_clock_freq(void);
 #endif						  /*Replace a call to get_clock_freq (after it is implemented)*/
@@ -82,9 +75,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
 #define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
 
-#define CONFIG_SYS_PCI1_ADDR           (CONFIG_SYS_CCSRBAR+0x8000)
-#define CONFIG_SYS_PCIE1_ADDR          (CONFIG_SYS_CCSRBAR+0xa000)
-
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -164,7 +154,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
 
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
@@ -254,7 +244,6 @@ extern unsigned long get_clock_freq(void);
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX		1
-#undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
@@ -277,9 +266,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_BOARD_SETUP		1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
-#define CONFIG_SYS_64BIT_VSPRINTF	1
-#define CONFIG_SYS_64BIT_STRTOUL	1
-
 /*
  * I2C
  */
@@ -287,7 +273,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x52
 #define CONFIG_SYS_I2C_SLAVE		0x7F
@@ -327,7 +312,7 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_UEC_ETH
 #ifndef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME         "FSL UEC0"
+#define CONFIG_ETHPRIME         "UEC0"
 #endif
 #define CONFIG_PHY_MODE_NEED_CHANGE
 #define CONFIG_eTSEC_MDIO_BUS
@@ -344,7 +329,8 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK16
 #define CONFIG_SYS_UEC1_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR       7
-#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_RGMII_ID
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
 #endif
 
 #define CONFIG_UEC_ETH2         /* GETH2 */
@@ -355,7 +341,8 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK16
 #define CONFIG_SYS_UEC2_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC2_PHY_ADDR       1
-#define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_RGMII_ID
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
 #endif
 #endif /* CONFIG_QE */
 
@@ -430,6 +417,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
@@ -442,7 +430,8 @@ extern unsigned long get_clock_freq(void);
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
-#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
 #define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
@@ -457,10 +446,10 @@ extern unsigned long get_clock_freq(void);
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 16 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
 
 /*
  * Internal Definitions