X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8560ADS.h;h=f0d7a594643b6849db687bf78b189d3c8304f578;hb=278b90ce786f73faf29aa522d5d101e1da006378;hp=2250c2fe019cbfd0a9ecc205203b578955157559;hpb=4d80051b63ff54f6b6f90fceb92cf87ab3401ecb;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 2250c2f..f0d7a59 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -19,25 +19,18 @@
 #define __CONFIG_H
 
 /* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
 #define CONFIG_CPM2		1	/* has CPM2 */
-#define CONFIG_MPC8560ADS	1	/* MPC8560ADS board specific */
-#define CONFIG_MPC8560		1
 
 /*
  * default CCARBAR is at 0xff700000
  * assume U-Boot is less than 0.5MB
  */
-#define	CONFIG_SYS_TEXT_BASE	0xfff80000
 
-#define CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 #define CONFIG_RESET_PHY_R	1	/* Call reset_phy() */
 
 /*
@@ -58,7 +51,6 @@
 #define CONFIG_SYS_CLK_FREQ	33000000
 #endif
 
-
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
@@ -74,7 +66,6 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -84,7 +75,6 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_NUM_DDR_CONTROLLERS	1
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
@@ -131,7 +121,6 @@
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
@@ -196,7 +185,6 @@
 #define CONFIG_SYS_LBC_LSDMR_4	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 #define CONFIG_SYS_LBC_LSDMR_5	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 
-
 /*
  * 32KB, 8-bit wide for ADS config reg
  */
@@ -219,21 +207,9 @@
 #undef  CONFIG_CONS_NONE	/* define if console on something else */
 #define CONFIG_CONS_INDEX       1  /* which serial channel for console */
 
-#define CONFIG_BAUDRATE		115200
-
 #define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
 /*
  * I2C
  */
@@ -264,9 +240,6 @@
 #define CONFIG_SYS_PCI1_IO_SIZE	0x100000	/* 1M */
 
 #if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -281,7 +254,6 @@
 
 #endif	/* CONFIG_PCI */
 
-
 #ifdef CONFIG_TSEC_ENET
 
 #ifndef CONFIG_MII
@@ -353,18 +325,14 @@
 
 #endif
 
-
 /*
  * Environment
  */
 #ifndef CONFIG_SYS_RAMBOOT
-  #define CONFIG_ENV_IS_IN_FLASH	1
   #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x40000)
   #define CONFIG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
   #define CONFIG_ENV_SIZE		0x2000
 #else
-  #define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
-  #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
   #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
   #define CONFIG_ENV_SIZE		0x2000
 #endif
@@ -380,32 +348,6 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-    #define CONFIG_CMD_PCI
-#endif
-
-#if defined(CONFIG_ETHER_ON_FCC)
-    #define CONFIG_CMD_MII
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
-#endif
-
-
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
 /*
@@ -416,14 +358,6 @@
 #define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR	0x1000000	/* default load address */
 
-#if defined(CONFIG_CMD_KGDB)
-    #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-    #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#endif
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
 
 /*
@@ -438,7 +372,6 @@
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #endif
 
-
 /*
  * Environment Configuration
  */
@@ -461,11 +394,6 @@
 
 #define CONFIG_LOADADDR  200000	/* default location for tftp and bootm */
 
-#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
-#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE	115200
-
 #define	CONFIG_EXTRA_ENV_SETTINGS				        \
 	"netdev=eth0\0"							\
 	"consoledev=ttyCPM\0"						\