X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8560ADS.h;h=ec0dad0df85b5b7bdf9462e1063b15f88f467a36;hb=55dabcc8f24598e2777f663de09ab55fbe1269da;hp=724575ac595bd1084ac45fb4f0b333a1c8639e61;hpb=d7869b2183d2b786e5410b97a5a6b2e630e7825e;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 724575a..ec0dad0 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -17,6 +17,8 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#include <linux/delay.h>
+
 /* High Level Configuration Options */
 #define CONFIG_CPM2		1	/* has CPM2 */
 
@@ -27,8 +29,6 @@
 
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
-#undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
-#define CONFIG_ENV_OVERWRITE
 #define CONFIG_RESET_PHY_R	1	/* Call reset_phy() */
 
 /*
@@ -57,16 +57,12 @@
 
 #define CONFIG_SYS_INIT_DBCR DBCR_IDM		/* Enable Debug Exceptions */
 
-#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
-#define CONFIG_SYS_MEMTEST_END		0x00400000
-
 #define CONFIG_SYS_CCSRBAR		0xe0000000
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
-#undef CONFIG_FSL_DDR_INTERACTIVE
 
 #define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 
@@ -113,12 +109,8 @@
 #undef  CONFIG_SYS_RAMBOOT
 #endif
 
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 
-#undef CONFIG_CLOCKS_IN_MHZ
-
 /*
  * Local Bus Definitions
  */
@@ -210,7 +202,6 @@
 /*
  * I2C
  */
-#define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
@@ -237,8 +228,6 @@
 #define CONFIG_SYS_PCI1_IO_SIZE	0x100000	/* 1M */
 
 #if defined(CONFIG_PCI)
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
 
 #if !defined(CONFIG_PCI_PNP)
     #define PCI_ENET0_IOADDR	0xe0000000
@@ -247,7 +236,6 @@
 #endif
 
 #undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
 
 #endif	/* CONFIG_PCI */
 
@@ -269,63 +257,9 @@
 
 #endif /* CONFIG_TSEC_ENET */
 
-#ifdef CONFIG_ETHER_ON_FCC		/* CPM FCC Ethernet */
-
-#undef  CONFIG_ETHER_NONE		/* define if ether on something else */
-#define CONFIG_ETHER_INDEX      2       /* which channel for ether */
-
-#if (CONFIG_ETHER_INDEX == 2)
-  /*
-   * - Rx-CLK is CLK13
-   * - Tx-CLK is CLK14
-   * - Select bus for bd/buffers
-   * - Full duplex
-   */
-  #define CONFIG_SYS_CMXFCR_MASK2      (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-  #define CONFIG_SYS_CMXFCR_VALUE2     (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-  #define CONFIG_SYS_CPMFCR_RAMTYPE    0
-  #define CONFIG_SYS_FCC_PSMR          (FCC_PSMR_FDE)
-  #define FETH2_RST		0x01
-#elif (CONFIG_ETHER_INDEX == 3)
-  /* need more definitions here for FE3 */
-  #define FETH3_RST		0x80
-#endif					/* CONFIG_ETHER_INDEX */
-
-#define CONFIG_BITBANGMII		/* bit-bang MII PHY management */
-
-/*
- * GPIO pins used for bit-banged MII communications
- */
-#define MDIO_PORT	2		/* Port C */
-#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ( \
-				(immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
-#define MDC_DECLARE	MDIO_DECLARE
-
-#define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
-#define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
-#define MDIO_READ	((iop->pdat &  0x00400000) != 0)
-
-#define MDIO(bit)	if(bit) iop->pdat |=  0x00400000; \
-			else	iop->pdat &= ~0x00400000
-
-#define MDC(bit)	if(bit) iop->pdat |=  0x00200000; \
-			else	iop->pdat &= ~0x00200000
-
-#define MIIDELAY	udelay(1)
-
-#endif
-
 /*
  * Environment
  */
-#ifndef CONFIG_SYS_RAMBOOT
-  #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x40000)
-  #define CONFIG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
-  #define CONFIG_ENV_SIZE		0x2000
-#else
-  #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-  #define CONFIG_ENV_SIZE		0x2000
-#endif
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
@@ -359,7 +293,7 @@
 /*
  * Environment Configuration
  */
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#if defined(CONFIG_TSEC_ENET)
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #define CONFIG_HAS_ETH2