X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8560ADS.h;h=e0d010a61802663cfa67136fc0256258942ceda6;hb=43ade93bdb0c8bd57382be810a05b3793749ce85;hp=49f6a353326468e3a923e6358a673dd1a4c12a32;hpb=8b485ba12b0defa0c4ed3559789250238f8331a8;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index 49f6a35..e0d010a 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -3,7 +3,7 @@ * (C) Copyright 2002,2003 Motorola,Inc. * Xianghua Xiao * - * SPDX-License-Identifier: GPL-2.0+ + * SPDX-License-Identifier: GPL-2.0+ */ /* @@ -12,19 +12,14 @@ * Please refer to doc/README.mpc85xx for more info. * * Make sure you change the MAC address and other network params first, - * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. + * search for CONFIG_SERVERIP, etc. in this file. */ #ifndef __CONFIG_H #define __CONFIG_H /* High Level Configuration Options */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ #define CONFIG_CPM2 1 /* has CPM2 */ -#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */ -#define CONFIG_MPC8560 1 /* * default CCARBAR is at 0xff700000 @@ -32,13 +27,11 @@ */ #define CONFIG_SYS_TEXT_BASE 0xfff80000 -#define CONFIG_PCI #define CONFIG_PCI_INDIRECT_BRIDGE #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ #define CONFIG_ENV_OVERWRITE -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ #define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ /* @@ -59,7 +52,6 @@ #define CONFIG_SYS_CLK_FREQ 33000000 #endif - /* * These can be toggled for performance analysis, otherwise use default. */ @@ -75,7 +67,6 @@ #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* DDR Setup */ -#define CONFIG_FSL_DDR1 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ #define CONFIG_DDR_SPD #undef CONFIG_FSL_DDR_INTERACTIVE @@ -85,7 +76,6 @@ #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_NUM_DDR_CONTROLLERS 1 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) @@ -132,7 +122,6 @@ #undef CONFIG_CLOCKS_IN_MHZ - /* * Local Bus Definitions */ @@ -197,7 +186,6 @@ #define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) #define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) - /* * 32KB, 8-bit wide for ADS config reg */ @@ -225,16 +213,6 @@ #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER -#ifdef CONFIG_SYS_HUSH_PARSER -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - /* * I2C */ @@ -265,9 +243,6 @@ #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ #if defined(CONFIG_PCI) - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - #undef CONFIG_EEPRO100 #undef CONFIG_TULIP @@ -282,7 +257,6 @@ #endif /* CONFIG_PCI */ - #ifdef CONFIG_TSEC_ENET #ifndef CONFIG_MII @@ -354,7 +328,6 @@ #endif - /* * Environment */ @@ -381,17 +354,10 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME - /* * Command line configuration. */ -#include - -#define CONFIG_CMD_PING -#define CONFIG_CMD_I2C -#define CONFIG_CMD_ELF #define CONFIG_CMD_IRQ -#define CONFIG_CMD_SETEXPR #define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) @@ -399,15 +365,8 @@ #endif #if defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_CMD_MII -#endif - -#if defined(CONFIG_SYS_RAMBOOT) - #undef CONFIG_CMD_SAVEENV - #undef CONFIG_CMD_LOADS #endif - #undef CONFIG_WATCHDOG /* watchdog disabled */ /* @@ -417,7 +376,6 @@ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ -#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ @@ -428,7 +386,6 @@ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data @@ -440,24 +397,16 @@ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif - /* * Environment Configuration */ - -/* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) #define CONFIG_HAS_ETH0 -#define CONFIG_ETHADDR 00:E0:0C:00:00:FD #define CONFIG_HAS_ETH1 -#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD #define CONFIG_HAS_ETH2 -#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD #define CONFIG_HAS_ETH3 -#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD #endif #define CONFIG_IPADDR 192.168.1.253 @@ -472,7 +421,6 @@ #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ -#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_BAUDRATE 115200