X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8560ADS.h;h=e0d010a61802663cfa67136fc0256258942ceda6;hb=0ff27d4a94637d4b1937c625d33212375bd118d9;hp=2250c2fe019cbfd0a9ecc205203b578955157559;hpb=4d80051b63ff54f6b6f90fceb92cf87ab3401ecb;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 2250c2f..e0d010a 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -19,11 +19,7 @@
 #define __CONFIG_H
 
 /* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
 #define CONFIG_CPM2		1	/* has CPM2 */
-#define CONFIG_MPC8560ADS	1	/* MPC8560ADS board specific */
-#define CONFIG_MPC8560		1
 
 /*
  * default CCARBAR is at 0xff700000
@@ -31,13 +27,11 @@
  */
 #define	CONFIG_SYS_TEXT_BASE	0xfff80000
 
-#define CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 #define CONFIG_RESET_PHY_R	1	/* Call reset_phy() */
 
 /*
@@ -58,7 +52,6 @@
 #define CONFIG_SYS_CLK_FREQ	33000000
 #endif
 
-
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
@@ -74,7 +67,6 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -84,7 +76,6 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_NUM_DDR_CONTROLLERS	1
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
@@ -131,7 +122,6 @@
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
@@ -196,7 +186,6 @@
 #define CONFIG_SYS_LBC_LSDMR_4	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 #define CONFIG_SYS_LBC_LSDMR_5	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 
-
 /*
  * 32KB, 8-bit wide for ADS config reg
  */
@@ -224,16 +213,6 @@
 #define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
 /*
  * I2C
  */
@@ -264,9 +243,6 @@
 #define CONFIG_SYS_PCI1_IO_SIZE	0x100000	/* 1M */
 
 #if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -281,7 +257,6 @@
 
 #endif	/* CONFIG_PCI */
 
-
 #ifdef CONFIG_TSEC_ENET
 
 #ifndef CONFIG_MII
@@ -353,7 +328,6 @@
 
 #endif
 
-
 /*
  * Environment
  */
@@ -380,15 +354,9 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO
 
@@ -397,15 +365,8 @@
 #endif
 
 #if defined(CONFIG_ETHER_ON_FCC)
-    #define CONFIG_CMD_MII
 #endif
 
-#if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
-#endif
-
-
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
 /*
@@ -438,7 +399,6 @@
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #endif
 
-
 /*
  * Environment Configuration
  */
@@ -461,7 +421,6 @@
 
 #define CONFIG_LOADADDR  200000	/* default location for tftp and bootm */
 
-#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
 
 #define CONFIG_BAUDRATE	115200