X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8560ADS.h;h=2e13fb52df236451ba77030bc67d5f3ddf42eccb;hb=8f1a80e99e4a838d1540cdb1d59ccc7785fe4618;hp=44b767919e2011664f15f449b5c491a1379627d3;hpb=4641c211f6e37454c30770521c4de79c725036b0;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 44b7679..2e13fb5 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -12,19 +12,14 @@
  * Please refer to doc/README.mpc85xx for more info.
  *
  * Make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
+ * search for CONFIG_SERVERIP, etc. in this file.
  */
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
 /* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
-#define CONFIG_MPC85xx		1	/* MPC8540/MPC8560 */
 #define CONFIG_CPM2		1	/* has CPM2 */
-#define CONFIG_MPC8560ADS	1	/* MPC8560ADS board specific */
-#define CONFIG_MPC8560		1
 
 /*
  * default CCARBAR is at 0xff700000
@@ -32,13 +27,11 @@
  */
 #define	CONFIG_SYS_TEXT_BASE	0xfff80000
 
-#define CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 #define CONFIG_RESET_PHY_R	1	/* Call reset_phy() */
 
 /*
@@ -59,7 +52,6 @@
 #define CONFIG_SYS_CLK_FREQ	33000000
 #endif
 
-
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
@@ -75,7 +67,6 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -85,7 +76,6 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_NUM_DDR_CONTROLLERS	1
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
@@ -132,7 +122,6 @@
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
@@ -197,7 +186,6 @@
 #define CONFIG_SYS_LBC_LSDMR_4	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 #define CONFIG_SYS_LBC_LSDMR_5	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 
-
 /*
  * 32KB, 8-bit wide for ADS config reg
  */
@@ -220,21 +208,9 @@
 #undef  CONFIG_CONS_NONE	/* define if console on something else */
 #define CONFIG_CONS_INDEX       1  /* which serial channel for console */
 
-#define CONFIG_BAUDRATE		115200
-
 #define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
 /*
  * I2C
  */
@@ -265,9 +241,6 @@
 #define CONFIG_SYS_PCI1_IO_SIZE	0x100000	/* 1M */
 
 #if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -282,7 +255,6 @@
 
 #endif	/* CONFIG_PCI */
 
-
 #ifdef CONFIG_TSEC_ENET
 
 #ifndef CONFIG_MII
@@ -354,18 +326,14 @@
 
 #endif
 
-
 /*
  * Environment
  */
 #ifndef CONFIG_SYS_RAMBOOT
-  #define CONFIG_ENV_IS_IN_FLASH	1
   #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x40000)
   #define CONFIG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
   #define CONFIG_ENV_SIZE		0x2000
 #else
-  #define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
-  #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
   #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
   #define CONFIG_ENV_SIZE		0x2000
 #endif
@@ -381,17 +349,9 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
@@ -399,15 +359,8 @@
 #endif
 
 #if defined(CONFIG_ETHER_ON_FCC)
-    #define CONFIG_CMD_MII
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
 #endif
 
-
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
 /*
@@ -440,21 +393,14 @@
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #endif
 
-
 /*
  * Environment Configuration
  */
-
-/* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
 #define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
 #define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
 #define CONFIG_HAS_ETH3
-#define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
 #endif
 
 #define CONFIG_IPADDR    192.168.1.253
@@ -469,11 +415,8 @@
 
 #define CONFIG_LOADADDR  200000	/* default location for tftp and bootm */
 
-#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE	115200
-
 #define	CONFIG_EXTRA_ENV_SETTINGS				        \
 	"netdev=eth0\0"							\
 	"consoledev=ttyCPM\0"						\