X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FMPC8544DS.h;h=091fd2e870d1d53c674beeffe7e01e0ba2c3d2ee;hb=d98b0523cfaaedeecb263b15c121c0727b0d80b9;hp=9743f031e0b495648dc8ea58c31d9164bae147f0;hpb=1d1ab638f8b5961e4972d29394e573afb39667be;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index 9743f03..0b69885 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -34,35 +34,26 @@ #define CONFIG_MPC8544 1 #define CONFIG_MPC8544DS 1 +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xfff80000 +#endif + #define CONFIG_PCI 1 /* Enable PCI/PCIE */ #define CONFIG_PCI1 1 /* PCI controller 1 */ #define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ #define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ #define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ + +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ +#define CONFIG_E1000 1 /* Defind e1000 pci Ethernet card*/ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#undef CONFIG_DDR_DLL -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ - -#define CONFIG_DDR_ECC /* only for ECC DDR module */ -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_DDR_ECC_CMD #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ -/* - * When initializing flash, if we cannot find the manufacturer ID, - * assume this is the AMD flash associated with the CDS board. - * This allows booting from a promjet. - */ -#define CONFIG_ASSUME_AMD_FLASH - -#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */ - #ifndef __ASSEMBLY__ extern unsigned long get_board_sys_clk(unsigned long dummy); #endif @@ -73,46 +64,46 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */ /* * Only possible on E500 Version 2 or newer cores. */ #define CONFIG_ENABLE_36BIT_PHYS 1 -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ - -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00200000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00400000 -#define CFG_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 #define CONFIG_PANIC_HANG /* do not reset board on panic */ /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ + +/* DDR Setup */ +#define CONFIG_FSL_DDR2 +#undef CONFIG_FSL_DDR_INTERACTIVE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_DDR_SPD -#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000) -#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000) -#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000) -#define CFG_PCIE3_ADDR (CFG_CCSRBAR+0xb000) +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef -/* - * DDR Setup - */ -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 + +/* I2C addresses of SPD EEPROMs */ #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ -/* - * Make sure required options are set - */ +/* Make sure required options are set */ #ifndef CONFIG_SPD_EEPROM #error ("CONFIG_SPD_EEPROM is required") #endif @@ -147,39 +138,39 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * Local Bus Definitions */ -#define CFG_BOOT_BLOCK 0xfc000000 /* boot TLB */ - -#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ +#define CONFIG_SYS_BOOT_BLOCK 0xfc000000 /* boot TLB */ -#define CFG_FLASH_BASE 0xff800000 /* start of FLASH 8M */ +#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */ -#define CFG_BR0_PRELIM 0xff801001 -#define CFG_BR1_PRELIM 0xfe801001 +#define CONFIG_SYS_BR0_PRELIM 0xff801001 +#define CONFIG_SYS_BR1_PRELIM 0xfe801001 -#define CFG_OR0_PRELIM 0xff806e65 -#define CFG_OR1_PRELIM 0xff806e65 +#define CONFIG_SYS_OR0_PRELIM 0xff806e65 +#define CONFIG_SYS_OR1_PRELIM 0xff806e65 -#define CFG_FLASH_BANKS_LIST {0xfe800000,CFG_FLASH_BASE} +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} -#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ -#define CFG_MAX_FLASH_SECT 128 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CFG_FLASH_CFI_DRIVER -#define CFG_FLASH_CFI -#define CFG_FLASH_EMPTY_INFO +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CFG_LBC_NONCACHE_BASE 0xf8000000 +#define CONFIG_SYS_LBC_NONCACHE_BASE 0xf8000000 -#define CFG_BR2_PRELIM 0xf8201001 /* port size 16bit */ -#define CFG_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/ +#define CONFIG_SYS_BR2_PRELIM 0xf8201001 /* port size 16bit */ +#define CONFIG_SYS_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/ -#define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */ -#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ +#define CONFIG_SYS_BR3_PRELIM 0xf8100801 /* port size 8bit */ +#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ #define PIXIS_BASE 0xf8100000 /* PIXIS registers */ @@ -194,125 +185,145 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ +#define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ +#define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ +#define PIXIS_VSPEED2 0x1d /* VELA VSpeed 2 */ +#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ +#define PIXIS_VSPEED2_TSEC1SER 0x2 +#define PIXIS_VSPEED2_TSEC3SER 0x1 +#define PIXIS_VCFGEN1_TSEC1SER 0x20 +#define PIXIS_VCFGEN1_TSEC3SER 0x40 +#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER|PIXIS_VSPEED2_TSEC3SER) +#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER|PIXIS_VCFGEN1_TSEC3SER) -/* define to use L1 as initial stack */ -#define CONFIG_L1_INIT_RAM 1 -#define CFG_INIT_L1_LOCK 1 -#define CFG_INIT_L1_ADDR 0xf4010000 /* Initial L1 address */ -#define CFG_INIT_L1_END 0x00004000 /* End of used area in RAM */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ -/* define to use L2SRAM as initial stack */ -#undef CONFIG_L2_INIT_RAM -#define CFG_INIT_L2_ADDR 0xf8fc0000 -#define CFG_INIT_L2_END 0x00040000 /* End of used area in RAM */ -#ifdef CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_ADDR CFG_INIT_L1_ADDR -#define CFG_INIT_RAM_END CFG_INIT_L1_END -#else -#define CFG_INIT_RAM_ADDR CFG_INIT_L2_ADDR -#define CFG_INIT_RAM_END CFG_INIT_L2_END -#endif - -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ /* Serial Port - controlled on board with jumper J8 * open - index 2 * shorted - index 1 */ #define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} -#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) -#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) /* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 -#define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,8544@0" -#define OF_SOC "soc8544@e0000000" -#define OF_TBCLK (bd->bi_busfreq / 8) -#define OF_STDOUT_PATH "/soc8544@e0000000/serial@4500" +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_EEPROM_ADDR 0x57 -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3100 /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ -#define CFG_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */ -#define CFG_PCI_PHYS 0xc0000000 /* 512M PCI TLB */ - -#define CFG_PCI1_MEM_BASE 0xc0000000 -#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCI1_IO_BASE 0x00000000 -#define CFG_PCI1_IO_PHYS 0xe1000000 -#define CFG_PCI1_IO_SIZE 0x00010000 /* 64k */ - -/* PCI view of System Memory */ -#define CFG_PCI_MEMORY_BUS 0x00000000 -#define CFG_PCI_MEMORY_PHYS 0x00000000 -#define CFG_PCI_MEMORY_SIZE 0x80000000 +#define CONFIG_SYS_PCIE_VIRT 0x80000000 /* 1G PCIE TLB */ +#define CONFIG_SYS_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */ +#define CONFIG_SYS_PCI_VIRT 0xc0000000 /* 512M PCI TLB */ +#define CONFIG_SYS_PCI_PHYS 0xc0000000 /* 512M PCI TLB */ + +#define CONFIG_SYS_PCI1_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCI1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCI1_MEM_PHYS 0xc0000000 +#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000 +#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */ /* controller 2, Slot 1, tgtid 1, Base address 9000 */ -#define CFG_PCIE2_MEM_BASE 0x80000000 -#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE -#define CFG_PCIE2_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCIE2_IO_BASE 0x00000000 -#define CFG_PCIE2_IO_PHYS 0xe1010000 -#define CFG_PCIE2_IO_SIZE 0x00010000 /* 64k */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0x80000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xe1010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xe1010000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ /* controller 1, Slot 2,tgtid 2, Base address a000 */ -#define CFG_PCIE1_MEM_BASE 0xa0000000 -#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE -#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 256M */ -#define CFG_PCIE1_IO_BASE 0x00000000 -#define CFG_PCIE1_IO_PHYS 0xe1020000 -#define CFG_PCIE1_IO_SIZE 0x00010000 /* 64k */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xe1020000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xe1020000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ /* controller 3, direct to uli, tgtid 3, Base address b000 */ -#define CFG_PCIE3_MEM_BASE 0xb0000000 -#define CFG_PCIE3_MEM_PHYS CFG_PCIE3_MEM_BASE -#define CFG_PCIE3_MEM_SIZE 0x00100000 /* 1M */ -#define CFG_PCIE3_IO_BASE 0x00000000 -#define CFG_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */ -#define CFG_PCIE3_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xb0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xb0000000 +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xb0100000 /* reuse mem LAW */ +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */ +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCIE3_MEM_VIRT2 0xb0200000 +#define CONFIG_SYS_PCIE3_MEM_BUS2 0xb0200000 +#define CONFIG_SYS_PCIE3_MEM_PHYS2 0xb0200000 +#define CONFIG_SYS_PCIE3_MEM_SIZE2 0x00200000 /* 1M */ #if defined(CONFIG_PCI) +/*PCIE video card used*/ +#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT + +/*PCI video card used*/ +/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/ + +/* video */ +#define CONFIG_VIDEO + +#if defined(CONFIG_VIDEO) +#define CONFIG_BIOSEMU +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_ATI_RADEON_FB +#define CONFIG_VIDEO_LOGO +/*#define CONFIG_CONSOLE_CURSOR*/ +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET +#endif + #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ @@ -320,15 +331,9 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #undef CONFIG_TULIP #define CONFIG_RTL8139 -#ifdef CONFIG_RTL8139 -/* This macro is used by RTL8139 but not defined in PPC architecture */ -#define KSEG1ADDR(x) (x) -#define _IO_BASE 0x00000000 -#endif - #ifndef CONFIG_PCI_PNP - #define PCI_ENET0_IOADDR CFG_PCI1_IO_BASE - #define PCI_ENET0_MEMADDR CFG_PCI1_IO_BASE + #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS + #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ #endif @@ -338,10 +343,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #ifdef CONFIG_SCSI_AHCI #define CONFIG_SATA_ULI5288 -#define CFG_SCSI_MAX_SCSI_ID 4 -#define CFG_SCSI_MAX_LUN 1 -#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) -#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) +#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE #endif /* SCSCI */ #endif /* CONFIG_PCI */ @@ -360,6 +365,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_TSEC3 1 #define CONFIG_TSEC3_NAME "eTSEC3" +#define CONFIG_PIXIS_SGMII_CMD +#define CONFIG_FSL_SGMII_RISER 1 +#define SGMII_RISER_PHY_OFFSET 0x1c + #define TSEC1_PHY_ADDR 0 #define TSEC3_PHY_ADDR 1 @@ -377,17 +386,17 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * Environment */ -#define CFG_ENV_IS_IN_FLASH 1 -#if CFG_MONITOR_BASE > 0xfff80000 -#define CFG_ENV_ADDR 0xfff80000 +#define CONFIG_ENV_IS_IN_FLASH 1 +#if CONFIG_SYS_MONITOR_BASE > 0xfff80000 +#define CONFIG_ENV_ADDR 0xfff80000 #else -#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x70000) #endif -#define CFG_ENV_SIZE 0x2000 -#define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * BOOTP options @@ -406,10 +415,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_CMD_PING #define CONFIG_CMD_I2C #define CONFIG_CMD_MII +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI - #define CONFIG_CMD_BEDBUG #define CONFIG_CMD_NET #define CONFIG_CMD_SCSI #define CONFIG_CMD_EXT2 @@ -421,40 +433,27 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 16 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ - -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ @@ -471,10 +470,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_ETHADDR 00:E0:0C:02:00:FD #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD -#define CONFIG_HAS_ETH2 -#define CONFIG_ETH2ADDR 00:E0:0C:02:02:FD -#define CONFIG_HAS_ETH3 -#define CONFIG_ETH3ADDR 00:E0:0C:02:03:FD #endif #define CONFIG_IPADDR 192.168.1.251 @@ -484,8 +479,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_BOOTFILE 8544ds/uImage.uboot #define CONFIG_UBOOTPATH 8544ds/u-boot.bin /* TFTP server */ -#define CONFIG_SERVERIP 192.168.0.1 -#define CONFIG_GATEWAYIP 192.168.0.1 +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_GATEWAYIP 192.168.1.1 #define CONFIG_NETMASK 255.255.0.0 #define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ @@ -495,100 +490,21 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_BAUDRATE 115200 -#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) -#define PCIE_ENV \ - "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \ - "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \ - "pcieerr=md ${a}020 1; md ${a}e00 e;" \ - "pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \ - "pci d.w $b.0 56 1;" \ - "pci d $b.0 104 1;pci d $b.0 110 1;pci d $b.0 130 1\0" \ - "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff;" \ - "pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff;" \ - "pci w $b.0 104 ffffffff; pci w $b.0 110 ffffffff;" \ - "pci w $b.0 130 ffffffff\0" \ - "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \ - "pcie1regs=setenv a e000a; run pciereg\0" \ - "pcie2regs=setenv a e0009; run pciereg\0" \ - "pcie3regs=setenv a e000b; run pciereg\0" \ - "pcie1cfg=setenv b 3; run pciecfg\0" \ - "pcie2cfg=setenv b 5; run pciecfg\0" \ - "pcie3cfg=setenv b 0; run pciecfg\0" \ - "pcie1err=setenv a e000a; setenv b 3; run pcieerr\0" \ - "pcie2err=setenv a e0009; setenv b 5; run pcieerr\0" \ - "pcie3err=setenv a e000b; setenv b 0; run pcieerr\0" \ - "pcie1errc=setenv a e000a; setenv b 3; run pcieerrc\0" \ - "pcie2errc=setenv a e0009; setenv b 5; run pcieerrc\0" \ - "pcie3errc=setenv a e000b; setenv b 0; run pcieerrc\0" -#else -#define PCIE_ENV "" -#endif - -#if defined(CONFIG_PCI1) -#define PCI_ENV \ - "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \ - "echo e;md ${a}e00 9\0" \ - "pci1regs=setenv a e0008; run pcireg\0" \ - "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \ - "pci d.w $b.0 56 1\0" \ - "pcierrc=mw ${a}e00 ffffffff; mw ${a}e0c 0; pci w.b $b.0 7 ff;" \ - "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff\0" \ - "pci1err=setenv a e0008; setenv b 7; run pcierr\0" \ - "pci1errc=setenv a e0008; setenv b 7; run pcierrc\0" -#else -#define PCI_ENV "" -#endif - -#if defined(CONFIG_TSEC_ENET) -#define ENET_ENV \ - "enetreg1=md ${a}000 2; md ${a}010 9; md ${a}050 4; md ${a}08c 1;" \ - "md ${a}098 2\0" \ - "enetregt=echo t;md ${a}100 6; md ${a}140 2; md ${a}180 10; md ${a}200 10\0" \ - "enetregr=echo r;md ${a}300 6; md ${a}330 5; md ${a}380 10; md ${a}400 10\0" \ - "enetregm=echo mac;md ${a}500 5; md ${a}520 28;echo fifo;md ${a}a00 1;" \ - "echo mib;md ${a}680 31\0" \ - "enetreg=run enetreg1; run enetregm; run enetregt; run enetregr\0" \ - "enet1regs=setenv a e0024; run enetreg\0" \ - "enet3regs=setenv a e0026; run enetreg\0" -#else -#define ENET_ENV "" -#endif - #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ "tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ - "erase " MK_STR(TEXT_BASE) " +$filesize; " \ - "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ - "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ - "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ + "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \ + "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ "consoledev=ttyS0\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=8544ds/ramdisk.uboot\0" \ - "dtbaddr=c00000\0" \ - "dtbfile=8544ds/mpc8544ds.dtb\0" \ - "bdev=sda3\0" \ - "eoi=mw e00400b0 0\0" \ - "iack=md e00400a0 1\0" \ - "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \ - "md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \ - "ddrregs=setenv a e0002; run ddrreg\0" \ - "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \ - "md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0" \ - "guregs=setenv a e00e0; run gureg\0" \ - "ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \ - "ecmregs=setenv a e0001; run ecmreg\0" \ - "lawregs=md e0000c08 4b\0" \ - "lbcregs=md e0005000 36\0" \ - "dma0regs=md e0021100 12\0" \ - "dma1regs=md e0021180 12\0" \ - "dma2regs=md e0021200 12\0" \ - "dma3regs=md e0021280 12\0" \ - PCIE_ENV \ - PCI_ENV \ - ENET_ENV - + "fdtaddr=c00000\0" \ + "fdtfile=8544ds/mpc8544ds.dtb\0" \ + "bdev=sda3\0" #define CONFIG_NFSBOOTCOMMAND \ "setenv bootargs root=/dev/nfs rw " \ @@ -596,23 +512,22 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ - "tftp $dtbaddr $dtbfile;" \ - "bootm $loadaddr - $dtbaddr" - + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" #define CONFIG_RAMBOOTCOMMAND \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ - "tftp $dtbaddr $dtbfile;" \ - "bootm $loadaddr $ramdiskaddr $dtbaddr" + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND \ "setenv bootargs root=/dev/$bdev rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ - "tftp $dtbaddr $dtbfile;" \ - "bootm $loadaddr - $dtbaddr" + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" #endif /* __CONFIG_H */