X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FM53017EVB.h;h=4f82389cedfa1b09f01747e046e7ba056ccfec4e;hb=46b5c8ed017958fc387ab86c71ae6c90abb6793c;hp=8d2fa614cd2e836297306f08a04c53fbce28547d;hpb=6d5d0c955e2ca035481bc133d453fccd065b80e8;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/M53017EVB.h b/include/configs/M53017EVB.h
index 8d2fa61..4f82389 100644
--- a/include/configs/M53017EVB.h
+++ b/include/configs/M53017EVB.h
@@ -18,46 +18,19 @@
  * (easy to change)
  */
 
-#define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(0)
 
-#undef CONFIG_WATCHDOG
 #define CONFIG_WATCHDOG_TIMEOUT		5000
 
-#define CONFIG_SYS_UNIFY_CACHE
-
 #ifdef CONFIG_MCFFEC
-#	define CONFIG_MII_INIT		1
-#	define CONFIG_SYS_DISCOVER_PHY
-#	define CONFIG_SYS_RX_ETH_BUFFER	8
 #	define CONFIG_SYS_TX_ETH_BUFFER	8
 #	define CONFIG_SYS_FEC_BUF_USE_SRAM
-#	define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#	define CONFIG_HAS_ETH1
-
-/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
-#	ifndef CONFIG_SYS_DISCOVER_PHY
-#		define FECDUPLEX	FULL
-#		define FECSPEED		_100BASET
-#	else
-#		ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#			define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#		endif
-#	endif			/* CONFIG_SYS_DISCOVER_PHY */
 #endif
 
-#define CONFIG_MCFRTC
-#undef RTC_DEBUG
 #define CONFIG_SYS_RTC_CNT		(0x8000)
 #define CONFIG_SYS_RTC_SETUP		(RTC_OCEN_OSCBYP | RTC_OCEN_CLKEN)
 
-/* Timer */
-#define CONFIG_MCFTMR
-
 /* I2C */
-#define CONFIG_SYS_IMMR			CONFIG_SYS_MBAR
-
-#define CONFIG_UDP_CHECKSUM
 
 #ifdef CONFIG_MCFFEC
 #	define CONFIG_IPADDR	192.162.1.2
@@ -81,8 +54,6 @@
 
 #define CONFIG_PRAM		512	/* 512 KB */
 
-#define CONFIG_SYS_LOAD_ADDR	0x40010000
-
 #define CONFIG_SYS_CLK		80000000
 #define CONFIG_SYS_CPU_CLK	CONFIG_SYS_CLK * 3
 
@@ -99,8 +70,6 @@
 #define CONFIG_SYS_INIT_RAM_ADDR	0x80000000
 #define CONFIG_SYS_INIT_RAM_SIZE		0x20000	/* Size of used area in internal SRAM */
 #define CONFIG_SYS_INIT_RAM_CTRL	0x221
-#define CONFIG_SYS_GBL_DATA_OFFSET	((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*
  * Start addresses for the final memory configuration
@@ -115,19 +84,14 @@
 #define CONFIG_SYS_SDRAM_EMOD		0x80010000
 #define CONFIG_SYS_SDRAM_MODE		0x00CD0000
 
-#define CONFIG_SYS_MONITOR_BASE		(CONFIG_SYS_FLASH_BASE + 0x400)
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
 
-#define CONFIG_SYS_BOOTPARAMS_LEN	64*1024
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
 #define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
-#define CONFIG_SYS_BOOTM_LEN		(CONFIG_SYS_SDRAM_SIZE << 20)
 
 /*-----------------------------------------------------------------------
  * FLASH organization
@@ -135,9 +99,6 @@
 #ifdef CONFIG_SYS_FLASH_CFI
 #	define CONFIG_FLASH_SPANSION_S29WS_N	1
 #	define CONFIG_SYS_FLASH_SIZE		0x1000000	/* Max size that the board might have */
-#	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
-#	define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#	define CONFIG_SYS_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
 #endif
 
 #define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_CS0_BASE
@@ -153,7 +114,6 @@
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CONFIG_SYS_CACHELINE_SIZE	16
 
 #define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - 8)