X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FIceCube.h;h=33c2ead32919387914ba5e437879b3e78464f091;hb=bb367b95f9204115bd6eac82e839b5590e6da4eb;hp=f8c94ec2c2cfa2e4f124ac94a99f2b72de4c607b;hpb=50bd0057ba8fceeb48533f8b1a652ccd0e170838;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h
index f8c94ec..33c2ead 100644
--- a/include/configs/IceCube.h
+++ b/include/configs/IceCube.h
@@ -30,12 +30,21 @@
  */
 
 #define CONFIG_MPC5xxx		1	/* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200		1	/* (more precisely a MPC5200 CPU) */
 #define CONFIG_ICECUBE		1	/* ... on IceCube board */
 
-#define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFFF00000	boot high (standard configuration)
+ * 0xFF000000	boot low for 16 MiB boards
+ * 0xFF800000	boot low for  8 MiB boards
+ * 0x00100000	boot from RAM (for testing only)
+ */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
+#endif
 
-#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH  */
-#define BOOTFLAG_WARM		0x02	/* Software reboot	     */
+#define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */
 
 #define CONFIG_HIGH_BATS	1	/* High BATs supported */
 
@@ -47,7 +56,6 @@
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 
 
-#ifdef CONFIG_MPC5200	/* MPC5100 PCI is not supported yet. */
 /*
  * PCI Mapping:
  * 0x40000000 - 0x4fffffff - PCI Memory
@@ -71,16 +79,11 @@
 
 #define CONFIG_SYS_XLB_PIPELINING	1
 
-#define CONFIG_NET_MULTI	1
 #define CONFIG_MII		1
 #define CONFIG_EEPRO100		1
 #define CONFIG_SYS_RX_ETH_BUFFER	8  /* use 8 rx buffer on eepro100  */
 #define CONFIG_NS8382X		1
 
-#else
-#define CONFIG_MII		1
-#endif
-
 /* Partitions */
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -126,11 +129,11 @@
 #endif
 
 
-#if (TEXT_BASE == 0xFF000000)		/* Boot low with 16 MB Flash */
+#if (CONFIG_SYS_TEXT_BASE == 0xFF000000)		/* Boot low with 16 MB Flash */
 #   define CONFIG_SYS_LOWBOOT	        1
 #   define CONFIG_SYS_LOWBOOT16	1
 #endif
-#if (TEXT_BASE == 0xFF800000)		/* Boot low with  8 MB Flash */
+#if (CONFIG_SYS_TEXT_BASE == 0xFF800000)		/* Boot low with  8 MB Flash */
 #if defined(CONFIG_LITE5200B)
 #   error CONFIG_SYS_LOWBOOT08 is incompatible with the Lite5200B
 #else
@@ -169,7 +172,6 @@
 
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
-#if defined(CONFIG_MPC5200)
 /*
  * IPB Bus clocking configuration.
  */
@@ -178,7 +180,6 @@
 #else
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
 #endif
-#endif /* CONFIG_MPC5200 */
 
 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
@@ -273,34 +274,31 @@
 
 /* Use SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_END	MPC5XXX_SRAM_SIZE	/* End of used area in DPRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE	/* Size of used area in DPRAM */
 
 
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_BASE    TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT		1
 #endif
 
 #define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC	1
+#define CONFIG_MPC5xxx_FEC_MII100
 /*
- * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
+ * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
  */
-/* #define CONFIG_FEC_10MBIT 1 */
+/* #define CONFIG_MPC5xxx_FEC_MII10 */
 #define CONFIG_PHY_ADDR		0x00
-#if defined(CONFIG_LITE5200B)
-#define CONFIG_FEC_MII100	1
-#endif
 
 /*
  * GPIO configuration
@@ -325,6 +323,9 @@
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
+
 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
 
@@ -340,13 +341,8 @@
 /*
  * Various low-level settings
  */
-#if defined(CONFIG_MPC5200)
 #define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL		HID0_ICE
-#else
-#define CONFIG_SYS_HID0_INIT		0
-#define CONFIG_SYS_HID0_FINAL		0
-#endif
 
 #if defined(CONFIG_LITE5200B)
 #define CONFIG_SYS_CS1_START		CONFIG_SYS_FLASH_BASE