X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FCRAYL1.h;h=6ababa1c50017fc5460f81fecc96edb386717e93;hb=d98b0523cfaaedeecb263b15c121c0727b0d80b9;hp=f1608e145f5576d5fceced18abcef6dcda7d72f9;hpb=96e21f86e8266ed40759e5495ee461265d7f6d28;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/CRAYL1.h b/include/configs/CRAYL1.h
index f1608e1..6ababa1 100644
--- a/include/configs/CRAYL1.h
+++ b/include/configs/CRAYL1.h
@@ -36,6 +36,13 @@
 
 #define CONFIG_405GP		1	/* This is a PPC405 CPU	*/
 #define CONFIG_4xx		    1   /* ...member of PPC405 family */
+
+/*
+ * Note: I make an "image" from U-Boot itself, which prefixes 0x40
+ * bytes of header info, hence start address is thus shifted.
+ */
+#define	CONFIG_SYS_TEXT_BASE	0xFFFD0040
+
 #define CONFIG_SYS_CLK_FREQ 25000000
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
@@ -45,6 +52,13 @@
 #define	CONFIG_PHY_ADDR		1	/* PHY address; handling of ENET */
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* early setup for 405gp */
 #define CONFIG_MISC_INIT_R	1	/* so that a misc_init_r() is called */
+#define CONFIG_NET_MULTI
+
+#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
 
 /* set PRAM to keep U-Boot out, mem= to keep linux out, and initrd_hi to
  * keep possible initrd ramdisk decompression out.  This is in k (1024 bytes)
@@ -64,6 +78,7 @@
  #define CONFIG_ETHADDR          00:40:a6:80:14:5
  */
 #define CONFIG_HARD_I2C         1		/* hardware support for i2c */
+#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SDRAM_BANK0		1
 #define CONFIG_SYS_I2C_SPEED		    400000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		    0x7F
@@ -74,32 +89,32 @@
 #define	CONFIG_SYS_HZ		             1000	/* decrementer freq: 1 ms ticks	*/
 #define CONFIG_SYS_HUSH_PARSER			1
 #define CONFIG_SYS_PROMPT_HUSH_PS2		"> "
-#define CONFIG_AUTOSCRIPT		1
+#define CONFIG_SOURCE			1
 
 
 /*
  * Command line configuration.
  */
 
+#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_BDI
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_ENV
 #define CONFIG_CMD_CONSOLE
-#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
 #define CONFIG_CMD_ECHO
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IMI
 #define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DATE
 #define CONFIG_CMD_RUN
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_SAVEENV
 #define CONFIG_CMD_SETGETDCR
+#define CONFIG_CMD_SOURCE
 
 
 /*
@@ -151,7 +166,7 @@
  */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_FLASH_BASE		0xFFC00000
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
 
 
 #define CONFIG_SYS_MONITOR_LEN		(192 * 1024)	/* Reserve 192 kB for Monitor	*/
@@ -233,12 +248,4 @@
 #define EEPROM_WRITE_ADDRESS 0xA0
 #define EEPROM_READ_ADDRESS  0xA1
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
 #endif	/* __CONFIG_H */