X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FCATcenter.h;h=550c462b8869b17a2b39cfbd9bb662f42307e0d3;hb=550650ddd0fde00f245bc3da72d7272844198394;hp=a44f3e16cc418b623db57784e1446f1817862f25;hpb=6d0f6bcf337c5261c08fabe12982178c2c489d76;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h
index a44f3e1..550c462 100644
--- a/include/configs/CATcenter.h
+++ b/include/configs/CATcenter.h
@@ -86,7 +86,11 @@
 # error "* External frequency (SysClk) not defined! *"
 #endif
 
-#define CONFIG_UART1_CONSOLE	1	/* Use second UART		*/
+#define CONFIG_CONS_INDEX	2	/* Use UART1			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
 #define CONFIG_BAUDRATE		115200
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 
@@ -184,7 +188,6 @@
 #define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
 #undef	CONFIG_SYS_EXT_SERIAL_CLOCK		/* no external serial clock used */
-#define CONFIG_SYS_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
 #define CONFIG_SYS_BASE_BAUD		691200
 
 /* The following table includes the supported baudrates */
@@ -210,17 +213,8 @@
 
 /* For CATcenter there is only NAND on the module */
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
 #define NAND_NO_RB
 
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
 #define CONFIG_SYS_NAND0_CE  (0x80000000 >> 1)	 /* our CE is GPIO1 */
 #define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2)	 /* our CLE is GPIO2 */
 #define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3)	 /* our ALE is GPIO3 */
@@ -545,13 +539,13 @@
  * GPIO0[30]	- EMAC0 input
  * GPIO0[31]	- EMAC1 reject packet as output
  */
-#define CONFIG_SYS_GPIO0_OSRH		0x40000550
-#define CONFIG_SYS_GPIO0_OSRL		0x00000110
-#define CONFIG_SYS_GPIO0_ISR1H		0x00000000
-/*#define CONFIG_SYS_GPIO0_ISR1L	0x15555445*/
-#define CONFIG_SYS_GPIO0_ISR1L		0x15555444
-#define CONFIG_SYS_GPIO0_TSRH		0x00000000
+#define CONFIG_SYS_GPIO0_OSRL		0x40000550
+#define CONFIG_SYS_GPIO0_OSRH		0x00000110
+#define CONFIG_SYS_GPIO0_ISR1L		0x00000000
+/*#define CONFIG_SYS_GPIO0_ISR1H	0x15555445*/
+#define CONFIG_SYS_GPIO0_ISR1H		0x15555444
 #define CONFIG_SYS_GPIO0_TSRL		0x00000000
+#define CONFIG_SYS_GPIO0_TSRH		0x00000000
 #define CONFIG_SYS_GPIO0_TCR		0xF7FF8014
 
 /*
@@ -783,7 +777,7 @@
  *
  */
 /* No command line, one static partition */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
 #define CONFIG_JFFS2_DEV		"nand"
 #define CONFIG_JFFS2_PART_SIZE		0x00200000
 #define CONFIG_JFFS2_PART_OFFSET	0x00000000
@@ -793,7 +787,7 @@
  * Note: fake mtd_id used, no linux mtd map file
  */
 /*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
 #define MTDIDS_DEFAULT		"nand0=catcenter"
 #define MTDPARTS_DEFAULT	"mtdparts=catcenter:2m(nand)"
 */