X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FBSC9132QDS.h;h=2994797117839218a05e07c58f1336bd7b5ed1d8;hb=69e173eb57d1f4848f070c83456096ba5d2ba1b4;hp=e8a8d299cd9d4c8d0c9e17e79ba6ff17e315406e;hpb=bd5053ffa5b8162257537bdb79ba829372423096;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h
index e8a8d29..2994797 100644
--- a/include/configs/BSC9132QDS.h
+++ b/include/configs/BSC9132QDS.h
@@ -11,7 +11,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_DISPLAY_BOARDINFO
 
 #ifdef CONFIG_BSC9132QDS
@@ -92,10 +91,8 @@
 #define CONFIG_FSL_PCIE_RESET		/* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
 
-#define CONFIG_CMD_NET
 #define CONFIG_CMD_PCI
 
-#define CONFIG_E1000			/*  E1000 pci Ethernet card*/
 
 /*
  * PCI Windows
@@ -320,7 +317,6 @@ combinations. this should be removed later
 /* NAND */
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_CMD_NAND
 
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
@@ -412,7 +408,6 @@ combinations. this should be removed later
 /* Serial Port */
 #define CONFIG_CONS_INDEX	1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
@@ -420,7 +415,6 @@ combinations. this should be removed later
 #define CONFIG_NS16550_MIN_FUNCTIONS
 #endif
 
-#define CONFIG_SERIAL_MULTI	1 /* Enable both serial ports */
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
 
 #define CONFIG_SYS_BAUDRATE_TABLE	\
@@ -440,7 +434,6 @@ combinations. this should be removed later
 /*
  * Pass open firmware flat tree
  */
-#define CONFIG_OF_LIBFDT
 #define CONFIG_OF_BOARD_SETUP
 #define CONFIG_OF_STDOUT_VIA_ALIAS
 
@@ -468,7 +461,6 @@ combinations. this should be removed later
 
 /* enable read and write access to EEPROM */
 #define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -485,10 +477,7 @@ combinations. this should be removed later
  * used for SLIC
  */
 /* eSPI - Enhanced SPI */
-#define CONFIG_FSL_ESPI  /* SPI */
 #ifdef CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_SPANSION
 #define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_SPEED		10000000
 #define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
@@ -583,17 +572,13 @@ combinations. this should be removed later
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_ERRATA
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING
-#define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
@@ -675,6 +660,7 @@ combinations. this should be removed later
 #define CONFIG_UBOOTPATH	"u-boot.bin"
 
 #define CONFIG_BAUDRATE		115200
+#define CONFIG_BOOTDELAY	10 /* -1 disable auto-boot */
 
 #ifdef CONFIG_SDCARD
 #define CONFIG_DEF_HWCONFIG	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
@@ -735,8 +721,4 @@ combinations. this should be removed later
 
 #include <asm/fsl_secure_boot.h>
 
-#ifdef CONFIG_SECURE_BOOT
-#define CONFIG_CMD_BLOB
-#endif
-
 #endif	/* __CONFIG_H */