X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FBSC9132QDS.h;h=108e92494d5b562ef9d0751e776151e8a25b0c46;hb=b39d1213e30717c435c8ed43411d573d435557cb;hp=59306dbaa9f5f84c3f400d74e108645943f2ff71;hpb=7453cb595cc17898a8227777b410b3e34a689c37;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h
index 59306db..108e924 100644
--- a/include/configs/BSC9132QDS.h
+++ b/include/configs/BSC9132QDS.h
@@ -11,7 +11,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_DISPLAY_BOARDINFO
 
 #ifdef CONFIG_BSC9132QDS
@@ -92,10 +91,8 @@
 #define CONFIG_FSL_PCIE_RESET		/* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
 
-#define CONFIG_CMD_NET
 #define CONFIG_CMD_PCI
 
-#define CONFIG_E1000			/*  E1000 pci Ethernet card*/
 
 /*
  * PCI Windows
@@ -399,9 +396,9 @@ combinations. this should be removed later
 
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* stack in RAM */
-#define CONFIG_SYS_INIT_RAM_END		0x00004000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000 /* End of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END \
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE \
 						- GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
@@ -411,7 +408,6 @@ combinations. this should be removed later
 /* Serial Port */
 #define CONFIG_CONS_INDEX	1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
@@ -419,7 +415,6 @@ combinations. this should be removed later
 #define CONFIG_NS16550_MIN_FUNCTIONS
 #endif
 
-#define CONFIG_SERIAL_MULTI	1 /* Enable both serial ports */
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
 
 #define CONFIG_SYS_BAUDRATE_TABLE	\
@@ -436,17 +431,6 @@ combinations. this should be removed later
 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 #endif
 
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
-
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400800 /* I2C speed and slave address*/
@@ -467,7 +451,6 @@ combinations. this should be removed later
 
 /* enable read and write access to EEPROM */
 #define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -484,10 +467,7 @@ combinations. this should be removed later
  * used for SLIC
  */
 /* eSPI - Enhanced SPI */
-#define CONFIG_FSL_ESPI  /* SPI */
 #ifdef CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_SPANSION
 #define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_SPEED		10000000
 #define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
@@ -582,11 +562,8 @@ combinations. this should be removed later
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_ERRATA
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
@@ -734,8 +711,4 @@ combinations. this should be removed later
 
 #include <asm/fsl_secure_boot.h>
 
-#ifdef CONFIG_SECURE_BOOT
-#define CONFIG_CMD_BLOB
-#endif
-
 #endif	/* __CONFIG_H */