X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FASH405.h;h=584f490680c0b26814fcbedcad27cf55a2d263bd;hb=bd84ee4c2020c3a6861f4bb2e7ea0fb49f82e803;hp=d03c05bf349fd141f95d5711aa82a50ac57e62ff;hpb=e09f7ab5749c345f924da272bea0521a73af5b11;p=kernel%2Fu-boot.git

diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h
index d03c05b..584f490 100644
--- a/include/configs/ASH405.h
+++ b/include/configs/ASH405.h
@@ -53,9 +53,13 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+#define CONFIG_NET_MULTI	1
+#undef  CONFIG_HAS_ETH1
+
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
@@ -132,39 +136,16 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
 
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1  /* verify all writes!!!         */
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
 /*-----------------------------------------------------------------------